I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hi,
I'm trying to store the DFU image in external flash. I already have DFU on the internal flash working.
When I enable support for the external flash and perform a...
I am developing a .NET C# project that receives data from the Nordic nFR52840 BLE Dongle via BluetoothLE, does Nordic provide any specific libraries for this purpose, or if...
I am migrating from the 2.6.1 development environment to 2.9.0 but am unable to compile due to some configuration issues.
My prj.conf configuration file is as follows: ...
Hi,
Recently I upgraded to nRF Connect SDK 2.6.1 and I was required to enable the GPIOTE in order to build properly. Doing this has significantly increased (nearly doubled...
Hello,
I'm reading about 700 values from an LSM6SDO gyro/accelerometers per second and need to store them, before sending them over bluetooth once where I store them is...
I’ve been working on creating a C++ application based on the NUS example, but I’m encountering an error. I’ve attached my application below. All I did was enable CONFIG_CPLUSPLUS...
ncs_add_partition_manager_config does not appear to be working. I am using ncs 2.1.0 and doing a build with MCUboot. Am I doing something wrong below?
I am using the following...
I open up a flash shared space in app and bootloader, write values from app, bootloader read, bootloader read values such as 0xFFFFF, and not ideal values, may I ask why this...
Hi, I'm upgrading the ncs version of my project from v2.7.0 to v2.8.0 and I'm no longer able to compile the project due to a linker error because the websocket_connect function...
Hi,
I followed the instruction ( https://docs.nordicsemi.com/bundle/ncs-2.5.0/page/nrf/samples/cellular/lwm2m_client/sample_description.html ) to build and run on my nRF9160DK...
Here it is suggested to gracefully terminate a thread by sending it a notification of any kind. But how can I terminate a thread that is in a waiting state with K_FOREVER...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
Hi,
I cleared my desktop and development environment.
So I rebuilt IDE using VSCode and NCS 2.9.0.
Everything works well without Intellisense in VSCode.
As above...
Hi,
We are using nrf52840, with SDK 16.0. we wanted to know that How does Garbage collection works?!
Does it reuse the allocated pages by erasing it or it uses the new...
I am just starting out. Trying to figure out how to interact with the board and my tool chain. I'm not sure how to flash a merged.hex file I made (serial_lte_modem) into the...
