We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I do not want to use the device id as my unique serial number of the nrf52840 chip and would like to generate my own . Where and how can I store this serial number...
I am using nrf51422 device with the SDK 11. I am running the hear rate application ble_app_hrs_pca10028_s130. When I connect to the device (using the nRF Connect app for ios...
Hi. I send 240 byte long messages using ble_nus_c_string_send at the moment.
How come the length field is a uint16_t if the max size is 247 bytes? Is it for future proofing...
I have a custom design buildt on ble_app_uart peripheral example from SDK 12.2.0. I use a timer that I start from case BLE_ADV_FAST in on_adv_evt to send a message to a display...
Hi,
I am using a PWM to control the output of an LED driver and I am implementing a soft_on function when powering ON the driver, so we have a start_PWM function that looks...
Hi, I want to start some projekt with BT840 module and use Keil to programming it. Also, I have Segger jlink programmer but I don't know how start. Can you give me some tips...
Hello,
we are using nRF52840 and have to directly use the CRYS API of the CryptoCell310.
In the documentation of the function CRYS_HASH_Update, the following is written...
When I use the battery to power on, I get NRF_POWER-> RESETREAS = 0x00010000. I check the register manual to see that it is GPIO wake-up. But I didn't configure GPIO wake...
Hello,
I am using Samsung Galaxy Tab A (2016) with android version 5.1.1 build LMY47V and I can not connect to the bluetooth module at all. In the log of the nrf Connect...
For an ADV_IND advertising event without any Scan Requests, what is the maximum amount of time that the radio's receiver will stay on?
Is this parameter configurable?
...
I am trying to configure SPI with BLE using softdevice S130. But SPI is not working properly when I used it with BLE, although it is working fine without BLE
Hello Nordic,
I am having problems getting the PPK to work with my nrf520840-DK application. I am happy to share my code with you, but first a hardware setup-description...
Hi,
Do you have an example in how to upgrade the firmware of the NRF52 family through UART via IAP? I am keen to update the FW of my product without the necessity of using...
Hi,
I'm developing a central application and I would like to be able to get the full device names of the peripherals I connect to. I know how to get the device name from...
