i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello ! I'm currently working on a SPI slave implementation for the nRF54L15.
I already read the spi-master-slave example.
The idea atm is basic and as follow :
My slave...
I have printed and assembled this circuit. The board is programmed with the help of a development board, but it doesn’t work. What could be the problem?
my code (led toggling...
nRF_Segger_RTT I want to port it from the high version SDK14.2 SDK to SDK7.1, is it OK?
Will it be difficult?
Can it be transplanted?
Tell me, thank you
Dear team,
I would like to have a function to measure the pulse width of the pulse that I generated and wonder if that is possible.
For example, I can generate one pulse...
I'm trying to create a demo beacon with an advertising interval of 5s and I only ever see a single advertisement from the device, following boot up. I've encountered this...
Hello,
I have an issue where my PC suddenly can't use any JLink after it had previously been working. Nothing changed to my knowledge that would have caused this issue other...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...
I've received a Nordic Semiconductor nRF9161 from a friend, who has been using it for a while.
I would like to completely reset the module, as it came when bought, so...
Im trying to use the BMA4xx driver (via i2c) in 2.7.0. The driver seems to init the device ok but I am getting a "SECURE FAULT" as soon as I do a sensor_sample_fetch . Attached...
Hi,
I spend few day trying to understand the issue with the provided sample (followed the tutorial) in the IoT fundamental lecture for the MQTT protocole. Then, I tried...
Hardware: nRF52840 (Custom Hardware)
Software: nRF Connect SDK v2.6.1
I am using the nRF52840 with custom hardware, where the device operates in two modes: Sleep Mode...
Hi,
In my project, I need turn on/off the hfxo, I found when i configure the hfxo, the nfc is not working. Here is my code:
void gps_server_function ( void * p1 , void...
HW: NRF52832 DK SDK: 17.1 SD:S132_7.2 Sw: ble_uart_c Issue: nRF52832 as a central to scan a peripheal(not nordic chip),the nRF Connect APP can discovery all the service, but...
I am trying to connect RPI(and/or Nvidia Jetson) with nrf9160 custom board(Icarusv2). I am using this custom board for other purposes and it works fine. For now I found only...
Hei,
I need to find the documentation for the NRF SDK 1.8, there's a page which has links to all the documentation versions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
