Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hey,
So I just finished setting up the hardware codec and I wanted to program these GPIOs to do certain tasks for me.
Specifically, I want the GPIOs 5-8 to be connected...
Hi, I want to create a partition setup (for the nRF5340) which I can use with future versions of the nRF Connect SDK, which means future versions of mcuboot and b0n. If we...
Hi,
I am testing two advertising sets on nrf sdk v2.6.0. Legacy advertising and long range. I tried to modify https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples...
Hello,
as part of my tries to use xip on nrf52840, I found that using the entire program on the external flash is impossible due to Errata 216 .
I check the FICR for my...
Hello,
I am needing to use two separate SPI masters, but I'm running out of pins. Are all of the pins compatible with SPI or are there some I should avoid. I'm thinking...
Hi all,
I have an application that is pretty simple. One master that needs to stream small payloads (sub 32 byte) to a receiving device. The payload is a fixed size and...
Question: nRF9161 Getting the high accuracy oscillator (HFXO) outside and sync with other nrf chips?
Basically I want to get the Clock Signal outside on a Pin, is it an...
We have 1 central device and 4 peripheral devices in which one of the peripheral is mobile device if we connect both mobile and other peripheral devices(nrf52840) the central...
I am testing an nRF9160 devkit with a TMP117 I2C sensor. My current goal is to read values from its registers.
My current code uses the function i2c_reg_read_byte to read...
Hi,
I've just received a nRF52840 DK and I'm trying to build and flash the blinky sample on it but the build failed continuously.
I also tried with other sample like the...
I want to convert raw hex bytes to utf8 format. The nRF5 SDK supported this with help of ble_srv_ascii_to_utf8() api. Is there something similar api available with nRF Connect...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am planning to set up the system as...
Good night,
I am doing the course "nRF Connect SDK Fundamentals" to learn about Zephir integration with nRF52840.
I am developing a RTOS solution based on the RAKWireless...
Hi,
I have an application that each 30 minutes connects to AWS, sends some data and then disconnects and goes to sleep. I have based my aplication on the asset_tracker...
I am trying to use the nrf5340 audio DK for the first time using one of the sample blink codes. I keep getting an error when first creating an application by copying the sample...
