Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi there
I have a question about the way the nRF52 radio handles on air addresses. I currently am developing custom software that uses the nRF52810 radio for a custom protocol...
I’m working with a Manufacturer-Specific Cluster (Attributes) in the Matter Template sample from NCS SDK v3.1.1, and it works fine with attributes. However, when I try to...
Hi, We designed a board using NRF5340-CLAA-R by following the Altium Reference design. Although when we tried to place an order with JLCPCB or PCBWAY, then informed that they...
Hi, I am pretty certain I have used RTTViewer before on the nRF9160, albeit not frequently. I cannot remember if I only used it on custom nRF9160 boards or if I used it on...
hello,
on our bm833 dev board, I scope (using a PIO) the time it takes for the bt_nus_send function to send 146 BYTES. The PIO goes to 0 after the callback nus_sent_cb has...
Summary
We are developing a Central application on the nRF7002 DK (nRF5340 SoC) using NCS v2.7.0 . The goal is to establish and maintain 11 concurrent Bluetooth Low Energy...
We're working on a project that interfaces an nRF9151 with a BQ40Z50 from Texas Instruments (via I²C / TWI / SMBus), and we've noticed the communication is unreliable. The...
Hi,
We are currently working on power optimization and want the device to wake up from the System ON state ( PM_STATE_SUSPEND_TO_IDLE ) using the RTC0 timer. However, I...
Trying to prototype a pinout on the nRF54L15 dev kit. We want P1.02 to be a GPIO pin instead of NFC. We followed the instructions to recover the device which erases the UICR...
Hi,
I am facing the following issue when i am calling west build from gitlab runner.
west: unknown command "build"; workspace C:\ncs\v2.5.0 does not define this extension...
Hi,
I am trying to come up with a different approach to SED reattachment using a backing off MLE session. Is there a way for the SED to keep on the polling even when in...
I'm working on an nRF9151 application that periodically sends small UDP packets (20-40 bytes) over both terrestrial LTE and satellite NTN networks. The device uses PSM between...
Hi,
We are doing some RF certification testing, EMC and also FCC, and wondered if you had advise on setting the modem on and transmitting, potentially if there is some...
Hi there. I have been working on a small project where I am using an encryption library for communication over ble. I am receiving encrypted token over ble charcteristics...
Description: Hello,
I am integrating a Protocentral MAX30001 ECG sensor with the nRF52DK (nRF52832) using the nRF Connect SDK v3.1.1.
The Issue: The sensor hardware is...
