Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi,
I noticed that latest nRF Sniffer BLE version support importing IRK, however, I can't make it successful, do you have a step-by-step guide for IRK importing on wireshark...
i just have a quick basic question about the device driver API, why does the samples/drivers/i2c_fujitsu_fram application not use a device tree node for the i2c peripheral...
Hi,
I am not sure how to explain or try to recreate the issue but I'll try my best.
Tools: I have an NRF52832 Development Kit bought from Digikey Canada. I am using...
Hi I have a programmed the nrf52832 custom design board(not the Development Kit) with Ble Becon example code given with SDK and checked the power consumption. It consumes...
Hello
We have always been able to go to the certification test house and complete cert without any issues. This is the first time that is mandatory to run the test using...
Hi
We are using NRF_51422 dongle in our university for Labs development with students
We were able to setup & install the NRF_sniffer. It is working with the command line...
I have an nRF52840 + nRF5 SDK 17.1.0 project that has been running on S140 7.2.0 and we're getting ready to lock some things in. But we happened to notice that there is a...
Hi,
I use peripheral_hr sample code of V1.7.1 version to send Data HRM by Bluetooth. the frequency is 22 Hz only.
I would like to icrease sample rate to 2 KHz, could i...
Screenshot of error message
Hello, I've followed the steps required on YouTube for setting up VS code with nrf Connect for desktop and the toolchain manager. It didn't...
Hi Team!
Currently I an working on disabling JTAG/Debug and SWD lines to protect code from read/write through any JTAG debugger.
For this, I have used nrfjprog utility...
Hi Support team,
I am testing nRF5340+nRF21540 with MT8852B now. I come across two issues in running the DTM FW from nRF Connect SDK v1.8.0:
1. nRF21540 TX gain value...
hi， I'm working on passthrough firmware(nRF5_SDK_17.1.0_ddde560)，I need to increase the priority of the serial port,see following code,When APP_UART_FIFO_INIT priority set...
Hello, in my zephyr application, I have uart1 configured as receive only using uarte at 921600 baud rate. Below is the description node:
I have a device sending a uart...
Hi,
We are using nRF52810 on a custom board, and when creating that board in NCS (in VScode), the Kconfig options are limited. We are not able to enable/disable the DCDC...
I have a project using NCS v1.8.0 where I enabled openthread.
For some reason, when trying to build `mbedtls/library/ecjpake.c`, the make command uses `-DMBEDTLS_CONFIG_FILE...
