Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi,
I'm trying to run an example in which is in below link but seems something is missing in the documentation seems also all commands returns "OK" but no response from...
i am using VS code, nrf Connect SDK version 1.7.0, nrf 5340 DK board. Attempting to run the CLI example.
The Cmakelist.txt:
#
# Copyright (c) 2020 Nordic Semiconductor...
I've got another question concerning a timeslot application.
In our timeslot application which is based on the nRF Mesh SDK timeslot.c implementation I noticed that if a...
I have a device using nRF52840 with SDK 15.2.0 and S140 6.0.0. It has failed with some kind of error. All core registers (including PC, LR) contain DEADBEEF. PRIMASK = 0xef...
I'm working on NCS 1.6.1.
I'd like to confirm if my method to get the RSSI is correct.
i test with a sample "peripheral_uart"
after BT connected, i printk the (NRF_RADIO...
I am testing the %XRFTEST Rx Test Command with the thingy91, with serial_lte_modem_2021-06-28_7a076c22.hex FW
and nRF Connect - LTE monitor software
I used the command...
The Repository link in the extension page on VS Code marketplace points to https://github.com/NordicPlayground/vscode-nrf-connect but that only returns 404 not found. I've...
Hello,
I am using the nordic nRF52840-DK and trying to connect to a nRF52840-Dongle and sending/receiving data to custom services and characteristics using pc_ble_driver_py...
Hi
I need to know, Is there any wifi module that supports for nrf5340 to communicate cloud or server??. If it is available kindly suggest us.
Thanks & Regards
Navin...
I am using Fanstel's BT840F BLE module which is based upon nRF52840 for my application. I am using PCA10056 DK to program it. I tried to program the BLE module on the DK with...
Hi,
We are using SDK13 and nrf52832.
I want to do multi pairing using Mode 1 Level 4.
Is there an example of multi-pairing and an example of deleting bonding individually...
I'm trying to update my devices from SDK 14.1 to SDK17. I've followed the pc-util instructions to create an SD+BOOT package, then after I'll send the updated application....
Hi,
I can use .overlay file to change the device tree setting of the nrf52840dk_nrf52840.dts.
However, my Board only has 1 button so I hope to "remove" 3 of the 4 buttons...
This discussion has been locked. I don't know why? and I don't know how to get it back.
devzone.nordicsemi.com/.../cannot-read-max30003wing-board-using-spi-communication...
I have an Zephyr application on the nRF5340 that I've been working on. I can debug fine in SES without a boot loader. However, when I add MCUBoot into the mix then everything...
