I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello,
I am doing BLE advertising on the nRF52833 and using nRF5 SK 17.0.2. I cannot set TX power above +4dbm from sd_ble_gap_tx_power_set(). I have checked in nrf_gap.h...
The "Flash" and "Erase and flash" actions wer working fine a few days ago，now it only execute "west build".
I pressed "Flash" or "Erase and flash", it just executed "west...
OK, I'm using Visual Studio Code with the nRF Connect extension. I'm playing around with some simple BLE code (trying to set up DIS and then a custom service). All of a sudden...
Hi Sir/Miss,
In original project, I use nRF52810. But, it's not enough flash in our customer adding requirements.
Therefore, I want to migrate project from nrf52810...
Hi,
I'm new on NRF connect with visual studio (I have programmed nordic devices before, nrf51), right now I am working with a nrf5340.
So far I have created a blinky...
Hello Everyone,
When I debug the GPIO interrupt of nrf5340, the edge trigger can be normal, but it will be triggered all the time when the level is triggered. Does anyone...
Hello,
I am trying to implement a system where the board waits for a character to be pushed to the RX buffer before reading it. The character would be sent by another microcontroller...
Users can often help each other and not rely on your staff.
I am trying to join a sample/matter_light_bulb sample to a newly formed Matter network.
The problem I describe...
Hello,
I am figuring out the fstorage functionality and I'm running basic example flash_fstorage from SDK 17.1.0 on my nRF52-DK. And I got the issues just on start.
At...
Hello,
I'm trying to control a motor via a mosfet. Setting the mosfet on/off with pin assignment works great, however pwm at any value other than 0 or max burn out the mosfet...
Hello,
We have a design that includes both the nRF52840 and the nRF9160. We are doing custom antenna designs in a miniaturized form factor and would like to specify required...
Hi
We are verifying the encrypt value and MIC value using a crypto tool.
The result is different depending on the setting of the packet S0 field.
If the S0 field is...
Hi,
I use this code for sampling analog input with 3.3 kHz and send it over BLE to PC , i use dongle to to read the sampled datas on nrfconnect tool for desktop. I tried...
Hi,
When connecting my Nrf52840 to a PC using BLE nfc, after connection is established, I encountered the following error : BLE_GAP_SEC_STATUS_OOB_NOT_AVAILABLE – Out of...
