Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
In build configuration i need to select nordic board . i have been using fanstel bt840 use nRF52840 QIAA, ARM Cortex M4F, 64 MHz . what board i have to select in this ? or...
Hi, we're having some problems and need help. We have a usage scenario: in HOST mode, the switching rate is 250k/2M every 10ms, the time slots of the two rates are different...
Hi I am trying to interface QSPI with NRF5340 dk board. I am getting build errors. I have used SPI-FLASH sample and it was working fine and I am trying to change the SPI-FLASH...
Hi,
in the new version of nrfx there is a function (nrfx _uarte _rx _new _data _check ( &uarte _instance ) , and how to get a similar result for the older version of nrfx...
Hi,
I have been testing the CAF click detector module and I find that any event callback after the click event takes almost 1000ms. That is the time between the actual click...
We are working on a project, with a working secure buttonless bootloader that works flawlessly. However I recently made it with bonds, and it works with all of the devices...
I'm experimenting with the Bluetooth Throughput sample in NCS v2.6.1. As I increase the distances between devices, I see strange gaps in the transmission from the Central...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi,
We are working on integrating nRF-Mesh-Library (iOS and Android) sdk into our app for mesh networking, it should support identifynode, provision, add app key and add...
I found a similar thread, but it did not solve the problem. When CDC-ACM is enabled in Device Tree, the dfu-util application cannot find the USB port. The Bootloader started...
Hi everyone
I am using nrf52840 costume board. and using NUS ( Nordic Uart Service ) as the basic start sample.
My desire:
1. UART0 and UART1 work in async mode with...
If I enter the prj.conf settings according to the lesson text then the firmware crashes with different provisioning functions from the smartphone app such as forgetting a...
It's looking more and more like a lot of my problems relate to a weak cell signal. Is the RF front end on the devkit known to be inferior to a normal cellphone? My personal...
Hello, I have connected a LR1110 module to a nrf52 (PCA10040) development kit using Arduino connectors. Anybody written a simple application regarding the interfaces?
It...
When I apply an Extra CMake build argument when creating a build configuration, it only takes effect on the first build, but none after that.
For example, I have added this...