Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
hi,
My custom board running Mesh SDK0.92 send and receive messages are normal.But after I replaced the MeshSDK in my program with Mesh SDK1.0.0, I was unable to send and...
Hello all,
I would like to establish connection between single central and two peripherals for bidirectional communication. I edited ble_multilink_central example and created...
I and new to programming the BLE devices and have just started out on the nRF52840 PDK and using Segger Embedded Studio for ARM v3.34. I have compiled and downloaded the ble_app_template...
I have to question:
1: if customer use relay node for mesh net, how much is the power consumption for one node? is there any passable to declare the power consumption to...
Hi,
I need to measure the capacitance of few capacitors for which I am currently using 3-channel CAP1203 IC from microchip.
However, I just came across the possibility of...
Hello,
I would like to establish bidirectional communication between single central and two peripherals. I referred ble multilink central example and made corresponding changes...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I set the WDT timeout in the application is 5s, when entering the BootLoader set the WDT time is 10s, how...
I am new to ble programming.
I am trying to find the best way to send json objects from android app to nrf52 chip.
What is the best way to send the json object to the...
Hello Sir,
I have developed small and compact product using nRF52832 Soc. Due to size limitation and device is portable. I have attached snap shot of power supply circuit...
Hello sir,
I am develop us product using nRF52832 chip on DK board use S132 soft device and its working well fine. So now we are designing hardware PCB of my product for...
Hello, I am trying to use adc with the uart so i can monitor the readings from adc. But when I include both drivers (nrf_drv_saadc , nrf_drv_uart) i got a confliction error...
Hello, although i have included every library and c file that is needed. i still get a declaration error. I'm almost sure that i enabled everything in sdk_config . I'm kinda...
In sd_power_system_off()，the nrf51822-board current is 2uA；And I think the current in sd_app_evt_wait() will be ~4uA(Is it correct)?
In sd_app_evt_wait(), the code...
In this example project
nRF5_SDK_12.3.0_d7731ad\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\main.c
/**@brief Function for initializing...
Hi,
I am trying to migrate to SDK14.2 from SDK12.
I have succesfully migrated to SDK13, but I am seeing linker issues with 14.
The linker comes with the following errors...
