Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
It looks like the nRF52840 only supports:
8 data bits
1/2 stop bits
even/no parity
So 7E1 is not a supportable mode...is this true? is there a possible work around...
Hi,
I am using nrf52840 and power it by voltage 3v using CR123A battery. As per datasheet minimum operating voltage is 1.7V. But i am facing controller reset at 2.5V. What...
How do we enable a PPI TASK for a GPIO output pin configured using zephyr GPIO driver API? ex: gpio_pin_configure_dt (&ex _pin , GPIO_OUTPUT );
If I just call nrfx_gpiote_out_task_enable...
Hi,
I'm having some trouble getting a device pointer for the OV7670 Camera. I've ported the OV7725 driver. It appears as if the program exits the driver before setting...
So I've been having an issue connecting JLink to programmer v2.2.0.
15:57:24.681
Using @nordicsemiconductor/nrf-device-lib-js version: 0.4.1
15:57:24.682
Using...
I'm trying to upgrade the nRF9160 modem FW on our nRF9160-DK. Programmer v2.2.2 indicates success but the at commands continue to return
at+cgmr
mfw_nrf9160_1.2.3
OK...
I am using the DPPI feature in the nRF5340 to trigger an SPI transaction from a GPIO edge with a delay.
In more detail:
GPIOTE IN event triggers RTC clear task
RTC compare...
Hello,
I've been trying to figure why calling sd_ble_gap_tx_power_set() continues to return the error NRF_ERROR_NO_MEM. I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
The application seems to stop at an instance where I invoke a Send call to send data over to a ble central, and the callstack looks as follows. Any way to narrow down the...
I'm using Ant sdh,I want to make system enter sleep,how to disable nrf_sdh_ant?
I usd this function to enable sdh,but can't disable sdh to enter sleep,how to use?
static...
Hello,
1.Which platform is recommended for developing Bluetooth mesh, nrf5-sdk-for-mesh or NCS?
2.What is the difference between nrf5-sdk-for-mesh and NCS?
3.What is...
Hello Devzone Community,
I am facing a run time, peripheral or sensor initialization error in a Zephyr based app, built using sdk-nrf v1.6.1, and its corresponding Zephyr...
