I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
When uploading programs to the nRF24 chip, is there a "single memory space" or is there a "bootloader-only memory space" and a seperate program memory space? or is it all...
Hi All
I am using S130, nRF51822, SDK12, My RTC1 compare events is connected by PPI to ADC, I have set it to generate an adc_ppi_event_handler after 6 consecutive compare...
Hello Team,
First Thanks to all Nordic support:)
My problem :
I have interfaced SGTL5000 with Nrf52832 (used SDK 16) I'm getting the audio data on aux connector and...
Hello!
I have problems with bt_shell sample from sdk-zephyr , when I use SoftDevice bluetooth stack( nrfxlib ).
When I switch on CONFIG_BT_EXT_ADV option in menuconfig...
I got an example that uses PO.13 for analogue input. It does this by referencing it as ADC_0. That seemed to work OK when I hooked up to PO.13 on the nrf9160-DK
Then I changed...
Hi, We are currently attempting to turn off unused parts of our RAM, and the app's linker space is configured to NOT use the turned on RAM. The problem is that the bootloader...
Good afternoon! I would like examples of projects on Soft device S140 long range to test the work of BLE Long Range HCI-USB host - need to be able to connect to them. (scannable...
I'm trying to achieve as close as possible to 48KHz (or 24KHz) LRCLK rate, in 24-bit mode (MCK/LRCLK = 48), on an nRF52832. With the values defined in `nrf_i2s_mck_t ` the...
I want to use libuarte. Target is nRF52832 and SDK17.0.0.2. Do I need to take workaround against Errata109 when using libuarte?
And, I done backport libuarte to SDK15.3...
I have been using nRF Connect SDK v1.2.0 to program my nordic thingy 91, however recently whenever i open IDE, Segger Embedded Studio gives the following error,
"Unrecoverable...
I am new to BLE and I have some question regarding Mesh and LPN which we cannot get a consistent result :
Assuming in a Mesh set up there are 2 Relay units (simply refer...
Hey,
I have an OLED trying to use, that is built in with a pcb design.
I don't know the manufacture to contact,
On my PCB datasheet says: the OLED Module QT-2028TSWIG02...
I created a TWI software module which runs well as standalone. Now I need to put together with BLE code to comunicate with Android APP. I'm stucked because when I initiate...
I am able to provision and configure 1 mesh device with the nrfMesh iOS app. I am able to successfully provision a second device, but when I configure a second device, the...
Hi,
I am trying to test and develop the DFU-OTA in nRF CONNECT SDK for nRF52832
I followed these link to develop i am using NCS v1.4.2
1. I have copied the peripheral_lbs...
