In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hi,
After successfully compiling and flashing both the blinky example and the ble_app_hrs on my nRF52840 I ran into an issue with ANT Broadcast TX example. The example...
Hello everyone,
I am working on a project that uses the nRF5340 microcontroller and Zephyr.
Initially I took an EVK-NORA-B106 development board that mounts the NORA-B1...
Hi,
I am using zephyr application. I need your guidance on how to set phy to 125 kbps?
I enabled some configurations regarding this please verify that and let me know...
I can't build the program.
Please help. Thanks
This log:
Rebuild started: Project: blinky_pca10040e *** Using Compiler 'V6.21', folder: 'C:\Keil_v5\ARM\ARMCLANG\Bin...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
Hi,
When I define my nrf52840 pin 0.19 as input put, and there is no connection to any sensor.
Then I use gpio_pin_get_dt() to get pin 0.19 status, the status is high...
I downloaded the nRF Connect SDK v2.7.0 and read the Release Notes. I installed the v2024.7.18 (pre-release) version of the nRF Connect for VS Code. As a first step, I created...
Greetings
I am trying to configure the nrf5340dk to use the i2c0 bus. I believe i2c1 is already configured, but for learning purposes, I want to figure out how to do this...
Hi,
When I DFU upgraded the bootloader of my firmware, I found that during the upgrade process, when ret_val = bl_activate() was executed, the pin would be pulled low. ...
The product page for the Thingy53 only shows hardware files for the v0.8.0 board revision, not the 1.0.0 or v1.1.0 board revisions.
https://www.nordicsemi.com/Products/Development...
HI all!
So I'm trying to use and modify parts of the Asset Tracker v2 application for my own project and when I created a new application with the pre-existing sample on...
Hello all,
I am trying to write some code to read the sensor values from two VL53L0X tof sensors, but I'm having some trouble.
My current code:
My devicetree:
...
I am using the cloud client example and connect to the nRF Cloud. I receive message fine on an interval and when I press the button.
I do not get any notification in my...
Hi all,
I am hoping to eventually integrate the crashlog functionality, but prior to this, I wanted to test the basic functionality with the flashlog. I have looked through...
