I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
When I developing application with nrf SDK,I can set device name by sd_ble_gap_device_name_set().
But when I turn to NCS,I should set device name such as CONFIG_BT_DEVICE_NAME...
Hello everyone I am using Nrf5340 Zephyr sdk v2.4.2 to broadcast BLE as a peripheral connecting 2 devices with Esp32 as central and phone at the same time, the following error...
Hello,
Does anybody know why I can not discover the service uuid as shown in the picture below?
I want to connect a sensor with this chip nRF52832, it's service UUID is...
Hello,
I'm using nrf52840 USB Audio headset application on nRF52840 DK. The nRF connect SDK version is v2.6.0.
I want to change the output to i2s out. The following are...
Hello, I have a few questions about sending code via J-Link. We are doing our project on vscode with 2.6 sdk. When working with nrf5340dk, flash via vscode was enough. However...
Dear lovely people from Nordic Seminconductor,
I have the nRF52840 dongle.
I installed the software ""nRF Connect for Desktop" on my Ubuntu 24.04
For that I ensured...
Hello,
I am using the NRF52840 dongle, and for my project I need to be able to send/receive data from a RaspberryPi and also send/receive large strings between multiple...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I want to use Emulated RTC driver functionality.
Therefore, I configured prj.conf file as (based on This Link ): CONFIG_RTC...
Good afternoon,
For a beamforming application in the Wi-Fi range, I am planning on using an nRF24L01 to generate the signal.
The signal would later be split into N different...
Hello,
So I have an IO Shield with the nRF5340 SoC. I have connected the IO Shield to the Port 12 of the nRF5340 Audio DK as shown in the schematic:
Connections:
Debugging...
Hi,
I am trying to sniff between my phone and a BLE device.
When I put the device in pairing mode, I can see it in the "advertising" list. Then I select it (but I don...
Hello Nordic Forum, I am working on a project involving data transmission from an nRF52840 board to an Android application, and I would appreciate guidance and insights from...
Hi.
There is MainThread and MeasureThread.
There are also two events that MainThread sends - BIT(0), BIT(1). These are Start and Stop.
In MeasureThread, we first wait...
I need to know further details about exactly how the nRF9160 modem behaves when changing between eDRX and PSM modes and when changing timer settings.
When using the AT+CEDRXS...
