I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi,
We're coming to the end of prototyping a project on the Thingy91X and are fine-tuning the power management. We have been able to implement a simple demo on the nrf9151dk...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi, I'm struggling to setup an application on the nrf54l15dk to control the nrf9151dk SLM over UART.
I have done the Cellular IoT Course and successfully controlled the...
I'm trying out the GNSS sample for the nRF9161 DK. I am trying to enable minimal assistance, but I get an error message with error code 65536: *** Booting nRF Connect SDK...
Hi,
Can MCUboot be used as a second stage bootloader (an application from the Secure DFU Bootloader over Serial Link standpoint) to be DFU'ed to existing devices which now...
Is it possible for users to regenerate the nRF9160 GNSS factory almanac data from public sources?
https://github.com/nrfconnect/sdk-nrf/blob/main/samples/cellular/gnss...
Hel lo, I am us ing a custom nRF5 2832-based b oard that has no DCDC circu itry (LDO onl y). What happened in NCS v2 .5.1
After power-on, the system did not st art (e...
Hello,
I am trying to measure a fast, impulsive signal from an amplified analog microphone using an ADC pin on the nRF54L15-DK. When I read the same signal using a 12-bit...
Our production facility has some concerns about using the OTP parameters. Specifically, they are concerned about writing the wrong value and then needing to scrap the device...
Hi,
We are developing a product based on nRF5340(ncs 3.1.0) and using MCUboot for OTA updates of both app core and net core.
During an OTA update, the following issue...
Hi Team,
I am working with nRF5340 and have a few clarifications regarding SWD protection (APPROTECT / ERASEPROTECT).
While the application is running, is it possible...
We have an unusual issue.
We are using the nrf 17.1 SDK for a custom board with the nrf52840 in tickless idle mode (RTC1) - using the available port_cmsis_systick.c for...
Hi there
I'm using the HCI UART bridge from NCS v3.2.1 in zephyr/samples/bluetooth/hci_uart with the provided overlay-all-bt_ll_sw_split.conf on an nRF54L15Dk and our Bluetooth...
This is just a request for an update to some documentation.
If you do a web search for "nrf NSIB" the first page this is likely to show up is this one . It's a good page...
Hi devzone team I'm working on the nRF54L05 with the FEM RFX2401C from Skyworks. I'm trying to configure the FEM with the "Simple GPIO" option. Here my overlay file:
After...
