Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Dear Support,
I encounted an issue when tried to connect with complicated wifi network recently.
The error info is as follwing.
"WPA: 4-Way Handshake failed - pre-shared...
Hi,
we use our code for beacons for very long time now. Unfortunately producer changed chip.
We were using NRF51802QF with SoftDeviceS130.
Now the chip is NRF52810QCAA...
I am receiving the following errors: [00:00:00.117,187] <wrn> bt_hci_core: opcode 0x2027 status 0x12 [00:00:00.118,133] <err> bt_id: Failed to add IRK to controller Which...
Hi,
I am new to board programming. I have a custom board with nRF52881. There is no USB port on the board to connect it directly to the PC. How can I connect the board...
Hi,
I see in the GNSS documentation for the nRF52840 that the GNSS modem performs scheduled downloads in Periodic Navigation mode, and from some testing, I found the download...
I am using nRF52832 Board for DFU. I want to implement static partition required for dfu operation. I would like to know that where shall I save the pm_static.yml file and...
The ActiveHardwareFaultsEnum supports a "TamperDetected" hardware fault, which is of interest for our product.
Using the general diagnostics server, it is possible to set...
If I use zb_zdo_mgmt_lqi_req() for dst_addr = local short address is the response resolved internally?
I have an application where I need to locate certain zigbee devices...
Dear Nordic support team,
We are using the SDK v2.6.1 to build targets for nRF52840 chips, and are using multiple configurations defined in a CMakePreset.json file.
It...
Hello!
I am currently running into throughput problems while using the Nordic Uart Service (NUS).
I am building a project for a peripheral and wanted to test the possible...
Hello,
We are implementing BLE FOTA for nRF52832. For that trying to load nrfutil tool. Its downloaded from official website. python is also installed successfully. when...
Attribute reporting is automatically handled by the ZBOSS stack which generates the Report Attribute commands. Is it possible to set the Disable Default Response bit in the...
When I start the debugger (both internal and Ozone) the registers view only shows the CPU internal registers; peripherals are not shown.
If I start Ozone manually I can...
This is same what same as in my previous ticket
With nRF9160 Ozone solution worked just fine but when trying to debug nRF9161 with Ozone I receive error on Ozone Console...