Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Dear support
Try to perform DFU OTA on my final target board and have an error state says - "payload(250 bytes) too long for MTU: 249 "during uploading stage, could anyone...
Hi,
I am developing application on NRF52840 with Zepyr 2.1.2 SDK, and I found two problems when using the example scan_adv, as follows:
Executing bt_le_scan_start in...
My team is developing for an nrf52840 on a custom design pre-production PCBA. Up till now we have been using nrf52840dk_nrf52840 in the"Board" field of the "Add Build Configuration...
Hi Team We’re using Nordic connect sdk 1.9.1 We’ve created a vendor service and defined multiple characteristics in same, We are using Nrf connect mobile app to fetch the...
Hi,
I am trying to capture provision packets from the BLE Mesh. I have nRF app for iOS. My iPhone is considered as a provision device, is it possible to provison another...
We are using SDK v1.9.1 with VS Code to develop software for a custom BLE board using the nrf5340 SoC. We also have/use a nrf5340-DK development board.
We generally update...
I want to make a card according to the NTAG213 specification package of NXP.
After I set the parameters, the default value for reading the card content will be NTAG203...
Hi,
We are running Zephyr 2.4 via PlatformIO on a nRF52840 based product. While spamming the nRF with a ton of BLE packets, after about 15 minutes or so we get the following...
Hi,
I have quite demanding SPI device which should send its data over BLE. Thanks to throughput example i was able to achieve maximum transfer speeds for synthetic tests...
Here are some values I got from the terminal:
11011110000000000001000000000010
00000010000001010000010000000011
00000011000000010000001011011110
I do not see the sign...
Good morning,
To my knowledge, the nRF52833 dk as well as the reference designs are FCC certified.
I'm currently searching the FCC IDs for these designs but I'm not able...
Hi
Using nRF52DK + SDK17.1 + S112
I have retarget enabled & using printf to output over UART (no DMA)
What's the best way to check if printf is busy outputting data...
Hi ,
What I am trying:-
-connect the custom board with nrf52840 chip using nrf52 dongle on pc with python.
-Already set some commands on custom board so when my pc ...
Hi:
i use the application note nA34's python file (dtm.py) to perform DTM PER test among 2 nRf52840 DK.
and in the LE_Test_Setup command ( the only set command which upper...
Hello,
Every time I try to run the sample gnss in SDK 1.8, I got this error gnss_sample: Failed to generate JWT, error: -8
Please can you let me what this error means...
