When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I am trying to generate encrypted data of particular data with IV and Key value by using mbedtls functions but when I try to do that in AES_CBC example code I am...
Hello,
I have multiple nrf52840 devices ( PCB's ) that act as peripherals and advertise data in BLE 5, and connectable in BLE 4.
We are able to connect to the device using...
I'm trying to enable DFU on our device but am getting a lot of issues.
I used Device Manager to upload app_update.bin and it worked. If I use Flutter example to upload firmware...
Hello everyone,
I am currently evaluating the nPM1300 Fuel Gauge with a LiFePo4 battery.
I would like to use nPM PowerUP to prepare the battery profile, but it appears...
hi support team,
i was testing mcumgr ota from uart, but found that the speed is slow how can i improve this?
i have change uart baud to 460800, but did not help. for...
Hi,
I'm using an nRF52840 DK to develop my prototype. Now I'm moving into the PCB design phase and I'm using a BLE ceramic antenna. I'll add a pi network footprint to tune...
I am using SPIS for my project. I am manually toggling CS for the peripheral. I get NRFX_SUCCESS for nrfx_spis_buffers_set() function. Also, when I probe the CS signal on...
Hi,
I am using the nrf52840 dongle board just to startup a project. I connected to the dongle a UART-USB converter to the dongle... but when I enable the UART into the firmware...
Hi Sir,
Please help to check do we support the ISO14064/ ISO14067 for the below part numbers.
1. Could you help to check do we pass the ISO14064/ISO14067?
If yes,...
I am implementing nrfx uarte on nRF52840 with ncs 2.6.1. I am using the example provided in modules\hal\nordic\nrfx\samples\src\nrfx_uarte as a reference.
Reason for using...
Windows 11, WSL2, NCS 2, VSCode
I want to be able to reboot my chip without the watchdog automatically being enabled on boot.
I cannot seem to disable it through the API...
Hello, the chip I am currently using is nrf52832 and the SDK version is SDK15.0. May I ask if all callbacks, interrupts, event handling, and main loops belong to the same...
Belows are that my development setup
sdk : sdk16
os : none
development tool : keil
To use the NRF7002, it is understood that the NRF CONNECT SDK must be used. However...
