Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I'm trying to disable proxy visibility of mesh node after its been provisioned by calling (from APP timer's context) proxy_stop() function. Though i'm getting NRF_FAULT_ID_SD_ASSERT...
Hi,
I am using nrf51822 chip for BLE application. In my circuit, I have used circuit supervisory components which is resetting the MCU whenever voltage level goes below...
Hello,
I have found out that we have shipped one product where NRF_CLOCK_LF_SRC_SYNTH was used together with the SoftDevice S132. I think at the time when it was implemented...
Hai team,
In my application , I am using nrf52832 , application took 26 microamps in runtime [peripheral - I2c] ,acclerometer and ble advertisements],here i need to put...
Hi Nordic,
My firmware is done and v1 beta is release, i will use it to flash my final production first batch with it.
What are the several good pratices to create...
Hello again,
I am trying to use the nordic PPK2 to estimate the battery capacity I would need. I would like to measure for a longer time in order to spot any strange behavior...
Hello,
We designed a custom board with nrf9160 (modem firmware v1.3.1) that runs an asset tracker type application.
The application uses both, LTE and GNSS:
logs sensor...
Hi I am currently using an nRF52840 SoC and I already have both I2C buses in use, as my application requires multiple I2C sensors with the same address. That means I can't...
I'm using SEGGER's SystemView tool to get some insights on my code. I see which interrupt number is activated, and want to figure out which code actually runs.
looking at...
Hello,
I designed my first custom board and I'm happy to have it running. When I developed my test application, I used printk() to send debug information to the console...
I am working with nRF connect SDK with nRF5340DK. I am compiling code using nRF connect (ncs-1.8.0) for VS code with nrf5340dk_nrf5340_cpuapp board.
prj.conf as below, ...
I am trying to store data to the UICR using SDK16, mesh SDK 4.2.0 and the nRF52840 chip.
I want to write to the UICR once on runtime and never again. To avoid messing with...
Hi, all
I have some issues about developing on nRF connect SDK with VSCode:
Go to definition for macro always jumps to the wrong place. For example, BT_DATA_BYTES...
Hi all, I am using nrf52 with Softdevice 113 v7.0.1 and SDKv16 and FreeRTOS v10.0.1 and I am experiencing some issues with FreeRTOS timers expiring earlier than expected when...
