Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
hello
I used nrf52840 with SDK15.3.
1.I use the example in this ticket and adjusted the baud rate to 9600 without hardware flow control. After SES is compiled, an "NRF_ERROR_SVC_HANDLER_MISSING...
MM8130-2600RA2
https://www.digikey.in/en/products/detail/murata-electronics/MM8130-2600RA2/1775922
This is RF connector used in DK. Please provide us the mating...
Hi there.
I am currently learning mqtt_simple from the nrf sdk example. So, I was trying to create a hex file that build using nrf9160, because I can't build it on thingy91...
Hi,
I have a custom board which uses P0.02 and P0.03. They are connected to interrupt signals from external devices.
To configure them as GPIO I set CONFIG_NFCT_PINS_AS_GPIOS...
Hi
I am developing a custom board using nrf9160. But before jumping to that process, I am using thingy91 (nrf9160 chip) as evaluation board for check all the firmware works...
Does ZBOSS support manufacturer specific attribute extension to standard clusters?
How about implementation of manufacturer specific clusters?
Are there examples one can...
Hi,
iOS NRF Mesh 2.2.3 version is working, but 3.2.0 unable to connect nodes,
Please suggest the procedure with iOS version in details.
Regards,
ArpitA
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and pca10056 board.
I use project nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\zigbee\light_control\light_bulb...
Hello! I will start by saying that I am new to embedded software development, and new to nrf boards in general. After successfully running the direction finding connectionless...
Hi Nordic Team,
I got the board yesterday, so I tried to debug on it. it seems no image is downloaded before shipped to me, as no log at all after power on, right?
So...
I have the next system perfectly working:
nRF52840 working as NCP to get OpenThread protocol.
STM32L486 as a host with a FreeRTOS
The communication between both is...
As far as I can see, when sending data via Bluetooth, the data is first stored in the buffer and then sent out together when the buffer is full. Is this the right idea? But...
Hello, We have an nRF9160 based IoT device in the pipeline, which should now be tested in a certified test lab. The purpose would be to perform a spurious emissions test using...
Good Day
I have enabled power saving on my nrf9160dk and am using NBIOT. In doing so I found that there was a 60 sec offset to what I selected and what I wanted the active...
Dear: IC : nRF51822_xxAA SD: s130_2.0.1 BL: SDK12.3 bootloader_secure with public_key AP: NUS MOBILE: iPhone 13 pro MAX with iOS 16.1.1 not always fail. but often How can...
