Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Hi!!
Now I am using sdk 14.0.0 / example / peripheral / spi / pca 10040 / blank / arm5_no_packs /
I am sending commands to ads 1192 with nRF 52832 DK as master and after...
I had an issue on using HID to control the media in Android. It worked fine at the first connection, I could play , pause and change the song on phone. But it couldn't control...
Hi I would like to confirm which NRF51822 models are the 0.35mm thin WLSCP package. I checked Avnet distributor and they say that NRF51822-CTAC-R7 is 0.35mm but the package...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
I need to make an android custom app (with UART functionality) so that only...
I'm trying to get a third party demo application working and I seem to be having an issue with the nrfx_spi_xfer function getting stuck waiting for the NRF_SPI_EVENT_READY...
Hi everyone,
I'm learning about proggram the nRF52840 dongle and I tried to code an interruption. Press the SW2 to turn on a LED
So, looking at this code, where did...
I am trying to make the nRF24LE1 as a sensor node. So I want to configure it to work as a receiver/transmitter and simultaneously use the ADC and UART. But the moment I added...
Hi all,
I'm using nrf51822 and ble_app_multirole_lesc example on SDK 12.3.
When I connect with "nrf connect" Android application for the first time, the bind is established...
Greetings. Finally ordered some NRF52832 board from HOLY IOT and spend few weeks trying to handle with them.
So, all about setup:
SDK: 15 (15.0.0_a53641a) @ Windows 7...
Hello, I have just started evaluating SoC nRF52832 and have built a custom board based on recommended diagram from the datasheet chapter 53.3. Actually, the board diagram...
Config
Using NRF52810 on a custom PCB with 32kHz + 32MHz crystals, very close to the reference schematic
S112 with SDK 14.2.0 in SEGGER Embedded Studio V3.30
A button...
In my application, I execute below code to start advertise when a button is pressed
err_code = ble_advertising_start(BLE_ADV_MODE_FAST);
APP_ERROR_CHECK(err_code);
...
Hello,
I am developing an application using the nRF51422.
For flashing and debugging the nRF, I use a ST-Link V2 debugger which uses SWD. The IDE I use is uVision.
I...
Hi
I have been succeed test SDK15.0.0 i2s example and got UART data.
UART started.<CR><LF> NRF_LOG_DEFAULT_BACKENDS_INIT started.<CR><LF> NRF_LOG_DEFAULT_BACKENDS_INIT...
