I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello,
I am migrating an application based on the old Nordic SDK16 to the NCS Zephyr SDK.
My workspace is using Zephyr commit f8f11338, nrfconnect/mbedtls commit de1b3f57...
Hello, I am trying to debug why my device is failing to work 100% of the time. What happens is an app makes a connection to the device, sends a command to the device, receives...
Hi all,
I' have a custom board with an nRF9161 chip. I have a custom connector to program it with SWDIO/SWCLK. For the moment I'm trying to detect my board with nrf programmer...
Hello!
I have a custom service that I try to implement on two nrf52840 DK, where one is supposed to act as a GATTClient and one is going to be a GATTServer.
The service...
hey there
i design my own board based on nRF5340, now i want to write a code for wireless boot loader on it with ble. on my board i have a nor flash for this goal. in part...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of that i need to implement some algorithms in it, i use the ld file to allocated a segment...
Hi,
After successfully compiling and flashing both the blinky example and the ble_app_hrs on my nRF52840 I ran into an issue with ANT Broadcast TX example. The example...
Hello everyone,
I am working on a project that uses the nRF5340 microcontroller and Zephyr.
Initially I took an EVK-NORA-B106 development board that mounts the NORA-B1...
Hi,
I am using zephyr application. I need your guidance on how to set phy to 125 kbps?
I enabled some configurations regarding this please verify that and let me know...
I can't build the program.
Please help. Thanks
This log:
Rebuild started: Project: blinky_pca10040e *** Using Compiler 'V6.21', folder: 'C:\Keil_v5\ARM\ARMCLANG\Bin...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
Hi,
When I define my nrf52840 pin 0.19 as input put, and there is no connection to any sensor.
Then I use gpio_pin_get_dt() to get pin 0.19 status, the status is high...
