I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...
hi support team，
i was testing smp_svr, i want to add button to my application that once i press the button and reset, the device will stay in mcuboot (serial port mode...
Hi,
I added build a conf to my project which has a prj.conf and select board. But the extension overwrites my configs with cache and extra cmake flags, which i dont want...
Hi there,
I'm currently trying to switch from actively advertising to a carrier wave test. This is the code snippet I'm currently debugging on SDK 17.1.0:
The code seems...
Hello, I use nRFCloud to send CoAP messages, and it's working fine under normal conditions. I am now trying to simulate a network loss, while sending some data. To do that...
I would like to create an ble5 sniffer from my thingy91. I saw that the sniffer is suitable for nrf52840 dongle and nrf52840 DK, and since thingy91 as an nrf52840 board i...
Hello,
I am currently developing a program that uses USB CDC-ACM for USB serial communication.
The USB serial communication is only used when the device is powered via...
Hello
I am developing an application on the nRF9160 SiP, that using CoAP protocol (over LTE) it connects to the nRF Cloud to transmit sensor data, get shadow register configuration...
Hello,
we are using nrf52840 with nrf5 sdk for thread and Zigbee v4.2.0.
We have been experiencing flash memory issues for a while now: https://devzone.nordicsemi.com...
Hello All, I am hoping to leverage Thingy 53's as the sensors (transmitting device) for tracking leveraging AoA. The nRF5340 DK works fine for this application as a sensor...
hi support team,
customer asks me about out 840 usb state, if we have usb low power state as below:
and below is listed in our spec or i n the USB standard ,
however...
Good night,
I am developing a Firmware for a nRF52840 created by RAKWireless RAK4631, with VSCode/Platformio/C++/FreeRTOS, and now I am changing the Architecture from a...
I am currently working with NCS v2.0.2 with toochain v2.0.2
I followed the steps in "How to change a workspace application SDK version" update to NCS 2.6.0.
when i build...
