Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi,
I have a custom board which uses P0.02 and P0.03. They are connected to interrupt signals from external devices.
To configure them as GPIO I set CONFIG_NFCT_PINS_AS_GPIOS...
Hi
I am developing a custom board using nrf9160. But before jumping to that process, I am using thingy91 (nrf9160 chip) as evaluation board for check all the firmware works...
Does ZBOSS support manufacturer specific attribute extension to standard clusters?
How about implementation of manufacturer specific clusters?
Are there examples one can...
Hi,
iOS NRF Mesh 2.2.3 version is working, but 3.2.0 unable to connect nodes,
Please suggest the procedure with iOS version in details.
Regards,
ArpitA
I use nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and pca10056 board.
I use project nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\zigbee\light_control\light_bulb...
Hello! I will start by saying that I am new to embedded software development, and new to nrf boards in general. After successfully running the direction finding connectionless...
Hi Nordic Team,
I got the board yesterday, so I tried to debug on it. it seems no image is downloaded before shipped to me, as no log at all after power on, right?
So...
I have the next system perfectly working:
nRF52840 working as NCP to get OpenThread protocol.
STM32L486 as a host with a FreeRTOS
The communication between both is...
As far as I can see, when sending data via Bluetooth, the data is first stored in the buffer and then sent out together when the buffer is full. Is this the right idea? But...
Hello, We have an nRF9160 based IoT device in the pipeline, which should now be tested in a certified test lab. The purpose would be to perform a spurious emissions test using...
Good Day
I have enabled power saving on my nrf9160dk and am using NBIOT. In doing so I found that there was a 60 sec offset to what I selected and what I wanted the active...
Dear: IC : nRF51822_xxAA SD: s130_2.0.1 BL: SDK12.3 bootloader_secure with public_key AP: NUS MOBILE: iPhone 13 pro MAX with iOS 16.1.1 not always fail. but often How can...
Hi,
I'm working on a legacy program using nRF52833 and nRF5 SDK using SoftDevice S113.
My application has two input GPIOs, and both can wake the MCU from System OFF. The...
Hello,
My professor bought several nRF9160 boards for our Electrical Engineering department to work on our final class project with. Several students are having a hard...
