I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi，nordic
I am using ses6.22a, the sdk is 1710 and mesh5.00. When I integrate the serial port case into the mesh sensor case, the serial port can work normally, but it must...
Hello guys, i'm attempting to record the radio_end event, and i tried to enable it with the following code:
However, the second line constantly crashes the chip.
In...
Hi:
I used the following command to install matter OTBR, but the following error occurred when executing this command;(sudo docker run -it --rm --privileged --name otbr...
hi,
I would like to purchase the following nRF-Desktop. It is a wireless BLE keyboard and mouse set.
https://www.nordicsemi.com/Products/Reference-designs/nRF-Desktop...
Hi,
I am using the nrf9160 and attempting to enable MCUBoot and secure boot. Is it correct that you still cannot use any form of TF-M with MCUBoot on the nrf53 or nrf91...
Hi,
I am currently using the NVS library with the nRF9160 and an external SPI-NOR flash device (MX25R6435F). I am getting concerned with the NVS library causing issues,...
Following Getting started with current measurements on the nRF9160 I applied the
to a Thingy:91 (disabled SERIAL, NCS-2.0.0). With that I get about 0,190 mA. That value...
Hi,
I would like to use the NRF52840 dongle (PCA10059) to transfer UART over BLE.
It seems there are some examples available that look promising, but after a day of struggling...
I face problem in k_sem_take() i build a nrf3540 board its successfully running in peripheral uart and some sample programs. while debugging peripheral connectionless rx and...
Hello. We manufacture the device on nRF 52840 and use NFC tag emulation to connect to BLE. We produced two batches of printed circuit boards and there were no problems. But...
Greetings,
In the product specification, it is specified to enable E0E1 high drive when using TRACEDATA[0..3] and TRACECLK. ( Pin assignments link )
Is this setting also...
Hi,
I'm working with a nRF9160 and nRF Connect SDK v1.7.0.
It looks like printk() is not outputting to UART, it previously was working when I was using nRF Connect...
Hi,
I am developing a project that uses TF-M to run some functions from a secure partition. The structure of the project is shown below:
├── lib │ ├── ... │ ├── blst.h...
I couldn't debug with Visual Studio Code, so when I reinstalled it, "Welcome", "APPLICATION", and "CONNECTED DEVICES"
only displayed "Loading..". Please tell me how to improve...
