When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello everyone,
I am designing a Bluetooth repeater that will be powered eather by USB or an embedded Li-Po battery. This device will run with the nRF52833 along with...
Hi,
I am working on a project, where I am trying to create a touch LED project using NRF52832. I have completed the prototype, its working is quite simple. The LED will...
Hello, guys!
We are using nRF51822 SoC with nRF5 SDK v12.3.0 and s130 SoftDevice. One of our desires is to use Software Interrupt (SWI) driver.
However, when I try to...
Hello all,
I am configuring a low power application for the nrf52832 board (custom board). This is a very low power application and I want the board to stay on sleep mode...
Hello everyone, I am working with a BMI160 6-DoF sensor. I have some drivers related to this chip. Using the Segger J-Link debugger the drivers just work fine without any...
I update a couple of device to mfw_nrf9160_1.3.2.zip.
Before that (1.3.1), my experience was to get a ENETDOWN, when calling " sendto" while the device has lost some the...
Hi.
I'm trying to add Bluetooth capability to the "Asset Tracker V2" project. I was able to do it on the nRF9160DK board. I could not find a working example to make the...
Hello,
windows10 x64.
i have used NCS1.9.1 and NCS1.9.99,now i want update to 2.0.99
how to install NCS2.0.99?
because nRF Connect for Desktop Toolchain manager no...
Hi,
1. How to calculate the Flash and RAM usages at runtime? I am able to do it static way but wanted to analyze this at runtime.
2. How to calculate the Heap usages at...
Hallo,
currently I try to optimise the functionality of my extended advertiser code. I found that there are also some call-backs defined for extended advertisers. The struct...
I use iOS nRF Connect APP to test DFU. But it failed with writing is not permitted.
The following is log message of nRF52832 device. 00> <info> app: Inside main 00> 00>...
Hi,
I am working on a system that runs a proprietary protocol, i.e. non-BLE, which works fine when it uses either uncoded links or S=8 ( LR125Kbit ) coded links, but I want...
Hello everyone, I am trying to send a string printed float number using the ESB protocol. I am using nrfConnect SDK 1.9.1 with nrf52832, started off with the supplied esb_ptx...
Respected,
I am using NRF connect for desktop for programming my actinius sensor (ICARUS IOT BOARD) but whenever I want to upload and reset the board using actinius programmer...
