I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi
I try to use in a mesh topology. I decided to send a string from client to nodes and receive its response. but I don't know how apply that. please help me to choose an...
hi , we have a nRF52840 DK when connected to PC via J-link there LED5 blinks . when i try to flash the code using Kiel IDE
get this error
using nRF connect the device...
Hello DevZone,
On my board I have a nRF52810 and a nRF52840. I want to implement a serial bootloader for the nRF52810 and have the nRF52840 program it.
I have looked...
Hello All,
We've got a new design using the nRF9160 - most of the PCBA's are connecting just fine to LTE-M - but I've seen a few with 'erratic' connections to LTE-M - I...
Hi, I can successfully build the openthread-cli sample but fail with all matter samples
Please refer the following log
> Executing task: nRF Connect: Build: light_bulb...
Hi
I'm just starting out to test the nRF9160 DK board and have just flashed the NB-IoT Asset Tracker as per the introductory video uploaded by Nordic here:
https://www...
I use a nRF9160DK for make my experiments:
nRF9160(modem) -> mdm_1.3.2
nRF9160(application) ->Serial Modem LTE (nRF SDK 2.0.0) with UART 2 and CONFIG_SLM_NRF52_DFU_LEGACY...
Dear Support Team，
Based on NCS 1.9.1, compile and download Hello Word firmware to nRF5340-DK (1.0.0), measure the voltage of all IOs with a multimeter as shown below: ...
After I ported my project to ncs2.0.0, I found that the RX of nrf9160 could not receive data. To this end, I modified at_client for testing and found the same phenomenon....
Hi All,
Later I will build a Custom Service, so I refer to ble_app_blinky.
According to the image below, I cannot clearly understand the difference between the two from...
I recently encountered a MCU crash problem. I think it is related to NRF_ LOG_ Process (). I used the simulation to catch the following scenarios. MCU crashes at this time...
Hi all:
SDK17.1.0
softdevice:s112
example:ble_app_hids_keyboard
I add a lot of function in my project ,including gzll, i2c,timer1 ,app timer ,rtc ,flash read/write...
Hi,
We are troubleshooting high power consumption on a custom nRF52832 board. It has taken us down to just
1. Enable RTC,
2. Setup GPIOs,
3. With and without NRF_POWER...
I am currently experiencing an issue using MCUmgr CLI over a serial connection provided by the on-board J-Link debuggers on nRF52 devkits.
When using MCUmgr CLI to send...
Hi,
currently I'm testing several options to transfer data in broadcast manner, i.e. in fact extended advertising due to the amount of data to transmit. A few days ago,...
