I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi.
For example, for the nRF52832 BLE chip, could it, in some manner, be only visible/communicate with a specific/particular smartphone app? How? using the MAC?
Regards...
Hello, I have a nrf5340dk communicating with nrf52840 dongle connected to a pc with UART baud rate of 2M. Connection parameters are:
7.5ms Conn interval
1ms Slave latency...
Background The adxl362 driver native to the zephyr kernel doesn't support FIFO operations, so I built my own out-of-tree driver that relies on a new accelerometer API instead...
I wish to add a firmware version to my project. Because we are hoping to use OTA for updating I have set the configuration paramater:
CONFIG_MCUBOOT_IMAGE_VERSION
in proj...
After working with arduino's and microprocessors like the ESP8266 and ESP32, I recently started toying around with a nRF52840 dev kit. After going through some tutorials,...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
Hi, I have a problem configuring the PPP Modem correctly and I'm not quite sure what i'm missing here.
I'm running the code on a custom board. We are using nRF52832 to talk...
Hello dear!
1- What is the relation(formulas) between current in uplink I uplink and the data packet size?
2- What is the relation between the iDRX PDCCH repetitions ...
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am running an application...
Hello. I am setting up the nrf9160dk and when I got to the step when I had to activate the SIM card. When I had to fill up my address etc. it didn't let me save it so I was...
Dear Sirs,
I have a sensor working as a peripheral and using the Nordic NUS service. I have a poblem discovering the two MSBits of the sensor's address when it connects...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement WDT and expecting to occur its event when the module becomes...
With the release of the Bluetooth 5.2 standard, also came the introduction of BLE Audio.
Since I am evaluating a SoC for bluetooth headphones, I stumbled upon the fact that...
I have an nrf9160dk setup with the bluetooth-hci-lpuart flashed to the nrf52 chip and a bt peripheral sample flashed to the nrf91. This works as expected. However, I am trying...
Hi Everyone,
We are currently stumped and are looking for guidance. A brief overview of what's needed from our client are as follows:
1) From the nRF mesh app, send...
