I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm referring to nRF5 SDK 17.0.2. In 'external/freertos/config/FreeRTOSConfig.h', the value 'configLIBRARY_LOWEST_INTERRUPT_PRIORITY' is set to 0xf, but the nRF51/52 only...
Hello! I'm trying to use this low power UART sample: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/peripheral/lpuart/README.html I have a problem...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard I add uart implementation from following...
I need nRF52840 revision 3 mounted development kit board, for trial rev 3 's approtect feature. But I don't know when is the rev. 3 mounted development kit board available...
when i make Rx output succefully.i add some configuration in main.c.i can print iq data.there is link that make me to learn to print iq data.
ok,i get iq data in here.but...
I'm trying out DFU functionality using nRF52840-PreviewDK and UART transport
It looks like I can disable the requirement for a signature when downloading an APP or SD (SoftDevice...
I have looked all over the product specification and the website and cannot find any information related to matching an antenna for this device.
What I am looking for are...
Hi I used your nrf toolbox Uart app to communicate from an Android phone to the module to send and receive bytes. The app was automatically updated a few days ago, now i cant...
Hi everyone,
I am not able to connect my J-Link plus compact with the programmer in nRF Connect.
It returns the error Unsupported device. The detected device could not...
Hi,
I am using SGTL5000 CODEC to playback the LINEIN and I am using the SGTL5000 driver from this link
I am using this I2S configuration
For I2S Loopback code itself...
I got an nRF52840 Dongle from someone else and started to see what I could do with it. The problem is, although I've downloaded everything needed including nRF Connect on...
I use: --nrf52840 --nRF5_SDK_17.1.0 --ESB.
Normally, 1:1 communication in one direction is performed from the module with nrf_esb_mode_t = 'NRF_ESB_MODE_PTX' to the module...
Hi,
I'm using the nordic nRF52840 - Dongle and a nRF52840-DK trying to send and write data with the pc-ble-driver-py library.
My problem is that i can communicate in...
Hi DevZone !
I am doing an application with nRF_ESB where I want to send and receive packets through diffenents nodes. Right now, I have 5 nodes, which 2 are repeaters in...
