Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
nRF Connect V 1.6.0
using samples/zigbee/network_coordinator against a nRF52840, I am trying to commission a larger number of devices to join the network. Currently 24 devices...
Firstly, my english is not good,
I am using nRF52840 and my IDE is Keil uvision 5, i want to know, where is the pins SDL and SDA
I am new developer, and please you can...
I have successfully formed a mesh and sending data in the format as below
" udp send ff03::1 1234 $01 " to udp '1234' socket
" udp send ff03::1 1234 $02 " to udp '1234...
Hello everyone,
I am currently testing the range of Nordic BLE modules for an indoor application. I am using BC805 (nRF52805) as peripheral and BM832 (nRF52810) as central...
I am re-implementing a custom error handler that stores error data and forms an error report after reboot, after having a success with it in nRF SDK 15.
In nRF SDK I could...
Hi,
I'm using Windows 10, Wireshark 3.2.17, python 3.9, pyserial 3.5.
I see this question has been asked before but the solutions did not work for me.
I get the...
Installed pynrfjprog on Ubunto 20.04 (native) via pip. Can open Highlevel api etc, however fails to detect nRF52 dev board as s probe and the logs indicate DLL failure.
...
I'm sorry, I don't know how this is reproduceable.
Yesterday and today my connection does not work. Sometimes . Yesterday it was OK early in the morning and in the afternoon...
I am using the SDK v17 with the Mesh SDK v5 and the nRF52 development kits and I'm using SEGGER.
SETUP: I have a mesh network with: 1 dimming client
1 dimming server ...
Hey Guys, currently, I am working on my masterthesis. I have to develop an mobile application which comminicates with the nordic board via BLE. I know that there is an existing...
Can you please clarify the typical eSIM current consumption when using eDRX?
Is the eSIM module on all the time? If so, what is the typical consumption?
If possible to...
The code shown below filters the duplicate MAC addresses, but I found in the previous development process that many Bluetooth devices only display the MAC address, not the...
Hii all,
i have a NRF52832 board with some sensors ..I coded it with SEGGER Embedded Studio . i Build and flashed and RUN successfully,
But after Disconnecting the board...
Hello , I am using the DTM in the NRF Connect.
Does you packet count preforms any CRC or other verification when receiving packets? I can not find any mention of BER (Bit...
