Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
At this link https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_2_Errata_v1.4.pdf, in 193 and 198 ID，this seems to be a mutually exclusive. In 198 workaround, .synchronize...
In the AGPS sample for nRF9160 "v1.5.1\nrf\samples\nrf9160\agps" main.c, there is option to set interval an and timeout in "gps_config" structure in "gps_start_work_fn" routine...
We ran into an issue when trying to use mcuboot on nRF53 with an external QSPI flash. In hal_nordic/nrfx/drivers/src/nrfx_qspi.c, the function nrfx_qspi_write has the following...
dear all：
I want to know how many beacons can be scanned by a gateway in the application of beacons.
At present, we have only actually tested more than 100 tags that scan...
Hi, Nordic Team. I'm using BC805M EK (nRF52805). In my code, I'm using SAADC (PPI interruption), TWI, BLE and System ON/OFF button .
Q1) I don't need RTS, CTS on the UART...
Hi
How to control two channels separately with one PWM instance?
I want to turn on/off the PWM output of each channel with any interrupt process.
app_pwm_disable() and...
Hi,
I am using nRF52840 , SDK 17.0.2/ble_peripheral. I am integrating Mesh SDK 5.0.0 libraries with ble_peripheral libraries in the nRF SDK 17.0.2 as per the documentation...
I created my first nRF52832 custom PCB board and I am having issues with poor RF performance. My project uses RSSI to estimate the distance between a peripheral and a central...
1.For example ,i have provisioned a few ble devices and added to the network by using an android phone .
Is it possible to do the provisioning with other android mobile...
Hi
I am using fds to store log in flash, after reading all data from flash, I am deleting record from flash.
But I found that Record ID incrementing from previous Record...
Hello,
I am creating my first bluetooth application and am having difficulties figuring out the interrupts. The application is working and is very simple - please see pseudo...
Hi everyone,
I have a fairly simple use for ADC: sample 4 channels (scan mode) every 10ms and store in RAM.
Every now and then (asynchronously) there will be a function...
Hello,
I am currently having issues with storing structure data in nRF52840 DK external flash. The default QSPI example present in peripheral sections work fine. But in...
Hi,
We are developing an IoT product using the nrf9160 controller. In the schematic of nrf9160 DK, they connected Ferrite Bead FB2 ( BLM15AX121SZ1D) to pin 101. please check...
