When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I noticed with the LTE Serial Monitor example code on a custom board with nrf9160 (and also the nrf91dk), the UART interface work initially but sometimes hangs. It...
Hi,
I am working with nRF52833 using the SDK17 Dynamic Pairing example. I was able to expand on it for my use case, and the application is now correctly receiving data...
Hello,
I am using NINA-B406 Custom board which have nRF52833 SOC and using Segger embedded studio with nRF5 SDK v17.0.2 for development.
I want to do the two functions...
Hi, Do you have any documentation at all for the experimental GPS driver? I can't find anything. Google just sends me to a few broken links. Best regards, Jan Erik BikeFi...
Hi, the specification of nRF5 SDK for Mesh v5.0.0. says the interrupt priority has two levels, named priority_lowest and priority_thread.
I am not clear on some things....
After installing nRF Connect for Desktop on macOS, I hit "Install" for Toolchain Manager, and then "Open".
This opens a new window for the Toolchain Manager, which says...
Currently, MQTT is required for nRF Cloud data transmission. We will be using LwM2M as the protocol to send data from our IoT monitoring device to our cloud platform. Does...
Hi, I have a bit strange problems with example project "pwm_library". At first I compiled with segger embedded studio and ran the project on my NRF52-DK board, and it worked...
I have used nRF52811 chip in my custom board.
1. Please provide the First time programming procedure using J-Link (J-Link-Pro tool) interface.
2. We have a nRF52840DK...
Hi teams,
Recently, I upgraded JLink driver to 7.5x and suddenly all of my nRF DK boards are not detected via USB.
All of my 4 DKs shows the same symptom. LED5 near JLink...
I am working on an embedded design that uses the nRF52840 MCU and 2x additional processors (Processor #1, Processor #2).
The intent of the system design requires that Processor...
dear all
I used the lvgl in zephyr. When I made a image rotation, I found that I copied some of the image pictures。Is there anyone in the forum who has encountered similar...
Dear friends: I am based on the following link: devzone.nordicsemi.com/.../device-firmware-update-dfu-with-mcuboot-bootloader Operation steps test the function of mcuboot...
Hello I am using sdk17.0.2 and nrf52840.
I used nrf52832 to combine ble_app_uart and crypto_aes_ctr codes. And now I'm going to move the code to nrf52840.
However, there...
Hi! I made a custom board with an external flash memory that communicate with nRF52840 through QSPI. I have some boards that works very well, but i have someones that freeze...
