Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I want to use the Nordic UART service from the ble_app_uart example in SDK 17.0.2 (running on nRF52DK) to use directed advertising to send data to a 9160DK client...
Hello,
Looking at the product specification, the nRF5340 system off current is specified at 0.9 uA. Can you please provide an example that I can run on the DK which can...
Hi.
As far as I know the SWD interface can be used to download/upload firmware and make debug, I would like to know if SWD also can make the function of sending and/or receiving...
Hi,
On a dice projet based on NRF52810. Sometime when I plug the battery charger the firmware crash at address 0x18808 and the call stack is empty !
This address is in...
Hello,
Can anyone please share some reference example for implementation code for central device which scan for available device.
I am using nrf52840.
Thank you
I have successfully installed the blinky example app on my new Nordic nrf 52840 Dongle - so that's good! :)
However, some things are not clear to me - so I would like some...
Hi,
I'm using nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\pca10040 & pca10056
Wants to send data packet over switch...
Hello,
I am trying to implement ble_dfu service into an existing project. The problem is I can not find an example in the SDK. I need to find out which macros to copy-paste...
Hello All,
I have a specific requirement to run 2 different functionalities from the same HEX file. Can someone suggest is there any means of special logic in the nRF52...
I have successfully ported the fatfs file system to my application code, but copying the files is very slow. I'm trying to modify the mass_storage.c file,follwing is my code...
I have two nRF52832 feather boards. Trying to set a simple connection between them so that board 1 sends beacons and board 2 receive them. Every few minutes, board 1 pair...
Greetings,
I am trying to run the scan_adv example from the samples. I am using the nRF52832 kit and SEGGER for running this sample. However, I face the error mentioned...
Hi everyone,
I am following this video step by step to create my custom board configuration https://www.youtube.com/watch?v=KSivO9Cf1TE&t=474s .
I follow every steps but...
Hi all,
My project can be built and run correctly on NRF SDK 1.5.0,
after updated to SDK 1.6.1 and rebuild, it failed and messages below:
Is there any idea for this...
