I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I want to make a secure pairing with Bluetooth. Let it first pair with the device, then connect directly without pairing. Maximum how many devices can I register?
Hi,
I'm using an nRF52832 in SDK v.17.1.0 and, starting from the ble_app_uart example code, I'm sending data from the board to another device. I want monitoring it with...
Hey all,
I'm looking for a bit of guidance here to nail a bus fault that happens about 30 minutes into the program.
The message is the following:
Reading through previous...
Hello
I am trying to test the esl example project.
Is there a simple, accurate, step by step guide for this?
Current documentation has some incorrect sections and when...
Hi Team
Customer want to use Bluetooth_Base_UUID (00000000-0000-1000-8000-00805F9B34FB) as 128 bit UUID base. They can use any other 128 bit UUID base but this one. When...
Hello, I'm working on an application with precise timing requirements. Basically I need to generate a short pulse and sample two channels during the pulse. In addition, I...
I use the nrf5340.
I want to filter 8 devices with different addresses.
When scan_filter_match() recognizes one of the addresses, can you quickly identify which of the...
Hello, I built a matter-over-thread firmware for nrf52840 on the Matter SDK 1.3-sve branch and NCS 2.5.0 version. It work well with Apple, Google and chip-tool, but commissioning...
Dear sir or madam,
I am facing a peculiar issue. In my application, I am using nrf52840 dongle and I am setting several GPIO pins as output pins with output value high...
Hello DevZone,
I am developing battery powered Zigbee end device. Using nrf Connect SDK 2.6.0 on nrf52840 chip.
I have issue that I am trying to solve. From time to time...
Hello there,
I was using 2.5 SDK on my development. Recenelty I updated the SDK to the latest of 2.7.0-rc3. I got many warnings.
Then, I created a brand new BLE NUS project...
We have a product that uses nRF52832 and works as a peripheral, connecting to mobile phones. Lately we have noticed that in some clients with Android phones, they cannot connect...
Hi,
I am using nrf52840 and SDK 16.0. I have already used SPI 1 and SPI 2 instances.
Now I am using SPI3 instance. Initially SPI 3 is initialized in non-DMA. and it worked...
Hello,
I am inquiring about the development guide for the coexistence of BLE and WiFi using the nrf7002dk board. Since I have recently transitioned from the nRF5_SDK development...