When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi All,
I am using ' NRF SDK v2.7 + NRF5340 DK + VSCode ' and cloned a official nrf ' matter light bulb ' sample.
My question is the default 'matter light bulb' uses NRF5340...
Hi,
we had used nRF52832 in our product. Our product is undergoing FCC & IC certification.
FCC & IC regulatory body had requested to provide Tone of tolerance (Power)...
Hi, I started my project with SDK version 2.6.1 (starting from the 'hello_world' example). I added mcuboot (CONFIG_BOOTLOADER_MCUBOOT=y). I followed the instructions in the...
Use nrf_modem_lib_init() to initialize the modem, followed by lte_lc_connect() to connect to LTE. However, it consistently fails to connect to LTE. After it times out, the...
HW: 52840DK PCA10056 3.0.1 2023.16
NCS SDK: v2.8.0
I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
Hello.
I am trying to use nRF Connect SDK v2.8.0 and nRF52840 to run Matter's Light Switch and Light Bulb.
I was able to confirm that it works with nRF52840-DK, but...
Hi there,
Our firmware is built on NCS 2.6.1 (soon to be ported to 2.7.0) and uses MCUboot.
I want to set REGOUT0 to 5 (which corresponds to 3.3V) and the `nrfjprog -...
I am trying to upgrade my project which is previously build with NRF connect SDK 2.6.1 to 2.8.0
I am getting this error while building
warning: NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Greetings,
when trying to compile simple GPIO configuration for NRF5340, the compile fails with:
In file included from C:/Apps/NordicSemiconductor/SDKs/v2.7.0/zephyr/include...
Hi
I have set up VS Code (1.93.1) on my Mac (mac OS 14.6.1) with nRF packages and zephyr installed. My nRF5340 DK is also found (however, instead of a nice identificaiton...
I am reaching out to inquire about the support for the indication method in the Nordic nRF52840. Could you please confirm whether this method is supported in the Nordic SDK...
There was no problem when the current version of ccache was 4.6.1. However, the current version of ccache, 4.10.2, behaves differently with the --specs option. It will do...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
What we need is to generate RSA key pairs and send public key to App to encrypt data...
Im trying to get SAADC to continuously sample using internal timer but im getting couple of samples and then it stops, tried everything but I'm obviously forgetting something...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
