Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
i get various answer about this, been in the rf design for a while, we used to make global antenna lenght on some give am ook circuit a tad shorter and then use a load cap...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
Hello,
We have built a device that uses the nRF52840 reference design shown below. With the configuration shown the board advertises as expected. If we replace either...
Hi, I try to use the example Bluethoot LE Wi-Fi provision in the nRF7002 DK and in the step to see the Wi-Fi Networks in the APP appers internal error.
Development kit...
Hi,
I'm developing a custom window cover device for Matter and I have a weird issue where Matter packets sometimes seem to take a very long time to go though. Window Cover...
Hi, It would have been quite useful if nRF54L15DK had CR2032 battery holder to carry around for experiments. since this board does not have it any recommendation to conne4ct...
I used the device tree to assist with schematic design, but after the PCBA was returned, I found that the peripheral functions could not be implemented normally.
It was...
NCS3.1.1, Windows10, VScode, NRF52840 custom board
With 3.1.1 I've discovered the paths in the "Edit build configuration" wizard are being broken and silently ignored during...
Hello DevZone,
May I know if there are any hardware SoCs and development kits that operate in Wi-Fi Halow(802.11ah) standard? Please point me out if there are. Thank You...
Hi,
I tested uart30 of NCS3.1.1, and found that I could not enter the low power consumption mode.But there is nothing wrong with uart20.
Related code usage:
prj.conf...
Hi,
I have a nRF5340 DK (PCA10095) that was working fine on the nRF Connect v4.2.1. I use the Direct Test Mode functionality.
However, after updating to v5.2.0, the DTM...
Hello, I’ve been exploring DECT NR+ on the nRF9151-DK using the DECT modem firmware. As it was already mentioned in multiple threads/other sources, there is no GNSS or LTE...
