I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
We're looking to integrate the NPM1304 in a product with a very small battery. As per the NPM datasheet we've selected a battery with a PCM.
We've previously seen...
We have a production system based on asset_tracker_v2 in V1.7.0 and V2.5.0. it normally connects and publishes fine 24/7. we have many sensors in the field. There are time...
Hello Nordic team,
I have a retail Thingy:91X device. IMEI: nrf-359404230239544
It connects to hello.nrfcloud.com, but I cannot add it to my own nRF Cloud account because...
We currently have a self-developed development board with NRF5340. The example program uses Bluetooth transparent transmission. Now I have added a GPIO pin: en_power is set...
When I was running the dm process of Connect SDK 3.0.2. I wanted to make one device as the initiator and six devices as the reflectors. I expect that the reflectors will not...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hi,
We have developed a custom board with both nRF52833 as the BLE beacon and nRF7001 as WiFi. We have chose to use patch antenna with UFL connector for both. When we tried...
Hi,
I have now run most of the YAML test successfully on the Matter TH and while I usually need to restart the TH between runs it seems fairly reliable now. Before sending...
Hi experts, I'm using the example under nrf-bm/samples/bluetooth/ble nus, and I've configured prj.conf, but it's not working.
I've been struggling with this for ages...
I am getting an error trying to get coded phy working with a sysbuild configuration for a nrf5340 custom board:
I am trying to follow the Bluetooth: Peripheral Heart Rate...
Hi,
I am using the nRF5340 for my project.
In the production stage, I am facing an issue: after programming the nRF successfully, when I perform a readback, it shows...
We have a Python script that is using pylink to open an RTT session and send some commands to the Firmware.
We have tried the JLinkRTTClient to send and receive command...
I’m working on reducing power consumption in my application using the LIS2DW12 sensor. I am currently turning off its LDO to cut power during low-power periods.
The problem...
Could you please help with providing terminal plating information for nRF52833? I have it noted as Sn but want to check if that’s matte or bright Tin.
Thank you,
Be...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
