I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi all.
After finishing some test I want to generate the binary for the MCU nrf52810 using zephyr. I have look in the zephyr folder and saw the zephyr.bin file. Is that...
Hello,
I'm currently developing with a nrf52832 (QFABB0) and I have to use pins 16,38,37 and 17 as gpio.
The problem is that when I have an error for pins greater...
Hi Nordic team
Q1. According to nrf Connect SDK documentation, Zigbee and Matter samples all supported FOTA (firmware update). Where can I find the DFU samples for Zigbee...
Hi，
When the friendship node has established with the LPN node, how to verify that the friendship sends a useful message to the LPN node?Has it any API to verify the message...
Hi If I permanently see 3.3v even when the application is not running does that mean it is busted? I also see a lot of spikes in the output I have placed an order for another...
Hi.
I have a problem using dfu bootloader.
SDK : 17.1.0
SD : 7.2.0
device : nrf52840
dfu code : secure bootloader pca10056_s140_ble
uECC : 13.0.0
I implemented...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I need to detect and monitor...
Hi,
I am using a Raytac MDBT50Q module on a custom board of mine. I have no 32kHz installed (which is available inside the module), VDD and VDDH are common and powering...
I'm porting code from my device which uses the nRF52832 to the 840 DK. My general process was to get the code developed on my own device to run on an 832 DK, then an 840 DK...
Hello everyone, I'm new here, and new to using the Nordic boards. I have a question regarding the RF connector in the nRF52840_DK. I am trying to do some RF measurements with...
Dear Team,
We notice that systemOFF current varying from 220 nA to around 500 nA for different devices. For some devices we are able to achieve 300 nA as mentioned in the...
Hi,
I'am using the ble_uart example on a custom board, where I have the issue that the BLE advertising is only available after a reset OR when I comment out the uart_init...
Hello,
I would like to implement beacon feature with a periodic (each 10s) advertisement data update.
This is an extrapolation of my code:
Is there some function that...
Hello,
The part i am using is NRF52840 Rev 2 (Build Code Dx0)
How can i exact know what revision or build code the SOC has ?
I want to determine in application what...
