Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I have a simple blinky application. I was able to get the application running and using the Qzone debugger. When I change the application te be a MCUboot compatible application...
Hello,
I just noticed something odd. When I just the hex file have provided with me
It worked perfectly, however, when I try to flash the lte_ble_gateway sample program...
Hi Nordic Support,
I'm getting this error while trying to connect two 52840 DK, one programmed with the connectivity firmware, and the other one with a sort of ble cli...
HI,
Following is the procedure to flash application we have tried:
Mass Erase
Write bootloader start address
Flash soft device
Flash bootloader
Flash application...
Hi,
I'm use ncs sdk what to send ADV_EXT_PDU Advertising, but this PDU every time send 8 advertising event, however, i'm notice that ncs sdk only use 8 second advertising...
I have a product under development that needs to send USB key codes to the PC that are outside the range that is supported by the USBD library and I am wondering the best...
Hi,
I´m developing a BLE-OTA driver for a BLE SoC and I try to use the nRF52840 dongle with my PC as the second device for the OTA mechanism by using Python and the pc_ble_driver...
I'm trying to create a HAL library to use it with zephyr application
From what I have read I need to create another module .
I can't figure out how to set up the module...
I am using the nRF52840-dk with the nRF Connect SDK v2.0.0 and for the development itself I use Visual Studio Code.
My Goal: Both the bootloader and the actual application...
Hi,
In my project, I have finished the application core code.Then I need to debug net core, but when I selected the "hci_rpmsg" target,and click the debug button.The debugger...
Hello my question is I am giving supply with lithium 18650 battery whic voltage is 3.7 to 4.2 volt but the battery falls very much below .
My question is when using HIGH...
Hello,
I'm working with NUS service and the nRF Toolbox app. I need to send multiple messages from mobile app to DK. How can I do that?. Is there a macro/script example...
I'm currently evaluating the nRF52840dk using the nRF Connect SDK to determine whether or not to port over our codebase to it from a Xiao nRF52 module I was using KVStore...
Hi,
I am trying to flash nrf52840 dk board with open thread binaries.
I see that, sporadically the device gets readback protection enabled.
I use the following command...
Hi
I have two PCA10121 and followed the instructions here to get the demo audio application to work.
The output of:
python3 buildprog.py -c app -b debug -d both
is...
