Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use the LED onoff example of the Nordic BLE Mesh template (Version : 5.0), using two nodes (One Client, One Server). The nodes are already Provisioned.
I want to know...
We have a requirement of sending data to nrf mesh app without provisioning. So Can we use health server model to send data on app without provisioning?
The reason we choose...
My understanding is that the Modem Library is a dedicated interface to the internal modem in the nRF9160.
We also need a 2nd modem interface to an external device that also...
Hi
We are developing a system based on nrf desktop application of nRF Connect SDK 1.90. There are 4 devices in this system: a dongle, a central device and two peripheral...
Hello Nordic Team,
From the below link and few other sources
nRF52840 SDK16 - BLE Descriptors and Notifications - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
I have read through similar posts, though none seem to talk directly about the DK and the JLink OB (SAM IC) missing bytes itself.
To start off with, I have created a basic...
From various pages I copied together this code to read the reset reason:
However, I believe most of those pages were for nRF5 SDK. (It's not always clear.)
Is this still...
Hi Nordic
I used the nrf_gpio_cfg_sense_input() API to initialize the GPIO4 for waking up nrf52832 from system off mode, This IO could wake up nrf52832 successfully, but...
These two func:"softdevice_ble_evt_handler_set "
and "softdevice_sys_evt_handler_set" suggests that there are two categories/sets of events grouped into system & BLE.
...
I'm a user of nRF52 DK with S132.
I want to modify the event handler in the example application code such as ble_uart_c.
Where can i find the full list and description of...
Hello
Can I use the LORAWAN module with NRF52833? if yes, is the LORA gateway also required to send the data to the cloud, or can it be done directly without a gateway?...
TX :52840
Software version：nRF5_SDK_16.0.0_98a08e2 hardware version：
RX:52820
Software version：nRF5_SDK_17.1.0_ddde560
My test method: send 60 bytes of data through...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
I am experiencing a strange behavior with SES 6.32, using GCC and I wonder if I should choose a different compiler.
COMPILING THIS PART OF CODE (I added line numbers for...
