Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
We have an existing product that uses a module containing NRF52832-CIAA
Due to supply issues we are looking to respin our board to use a different module that contains NRF52832...
When I reset the device and in some time connect it to JLinkRTTViewer, it shows only 11-12 first messages after the reset. Which parameter I should change to increase number...
Hi, I tried to create standalone project based on SAADC example from nRF SDK. I copied all neccesary .h files etc., changed the include directiories. But then appeared some...
I want to try NRF52811 EYSNCNZWW with Jtrace but i am not getting how to implement this.
I have Cortex-m Reference board which uses STM32F407 micro controller, it has dedicated...
Hello, I found this blog post in google and I decide to try it. I have couple of NrF52810 currently that we struggle with the limited space and the solution described in the...
Hi,
I have an issue with the first version PPK coupled with an nrf52840dk. I used to measure the current on the board through the nRF Connect desktop app on Linux and it...
Hello,
I'm looking for AoA antenna array reference design which could be used to create an actual device, but have not been able to find anything.
Thanks,
Billy..
While connecting with one NRF Development kit and Android NRF blink app mobile code, data is getting received properly.
But with some changes in development kit code ,We...
Hi,
I am using memfault with sdk 1.6.1 and want to get the reboot reason in my code. it is shown on boot and it seems the nordic register NRF_POWER->RESETREAS is then reset...
Hello Team, Could we control the 64MHz clock for some peripherals? I know that it is controlling by the clock control system itself and no way to configure it by the user...
Hi
When I generate a Zephyr Project with SES I get all c-files from CMakeLists.txt in the SES Project tree.
But I want also the h-files in the project tree.
How can...
We have developed our own application board with the nRF9160 on it according to the reference design.
The modem is connected to an application controller by UART (no HW...
when i connect NRF9160-DK (version 0.8.5 )to the CMW500 for CAT-M test, we have send the below three commands
AT+CFUN=4 AT%XSYSTEMMODE=1,0,0,0 AT+CFUN=1 to
the NFR9160...
Hello, all.
I'm using nRF52833, pca10100.
What I'm trying to do is just manually disconnect.
So, I referred to the Multi-link Central example. Multi-link Central is...
