When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I use nRF52832 as a central device. I also use ble_app_uart_c as a SDK(17.0.2) . I would like to connect my peripheral which is my phone(iPhone 6) and i want to see my phone...
Hi,
I'm on pre-product of BLE Advertisement packet scanner.
My product is gathering the adv packets from a bunch of BLE tag about 20~30 tags.
So, I use two nRF52832...
Hi,
I want to add bonding information manually.
1.can I assume IRK key will be constant for multiple peripherals?
2.if IRK only key is available, can i add it to peer...
I am finding that the voltage measurement is about .52 volts off when measuring Vdd I have set up a power supply and connected it to external power. My saadc is set up with...
Hi,
I am starting to finalize a development stage and was looking at the current consumption of my device. I noticed, that when something connects to it and is starting...
Hello there,
we get the following assert:
"00> <t: 480881>, app_error_weak.c, 98, Softdevice assert: 88996:0"
The board is rebooting constantly after 3 ... 7 minutes...
I tried to build the example project for UART serialization demo, "ble_app_hrs_pca10040_s132_uart". It failed with 3 errors, see attached image.
It is SDK 17 and SEGGER...
Product: nrf52840 DK
Softdevice: 17.0.2
Hello,
I would like to start with a very humble statement that I am new to this nrf52 SoCs and would appreciate any of your...
Hey everyone,
I am playing around with Nordic Cloud, Thingy:91 with the Asset Tracker v1 and the Nordic Cloud RestAPI.
I happened to see in the process, that the unix...
Hello,
I contact to you because a customer bought the development tool part number n RF52-DK, and one received the product, they noticed that there was on the box of the...
I use nRF52 DK as a central devices and i have also other nRF52 DK and use for a beacon. I would like to show my beacon's RSSI value on the UART Terminal(Realtek,Termite exc...
Hi,
I have done buttonless DFU in Custom board using NRF52832. My code with DFU is working fine in the nrf52832 Development kit. While I am trying in a custom board. My...
I'm developing for nRF52 DK
using SDK 17.02
Segger 5.10b
I'm developing a service to read pin 12 where I'll have a square wave signal of about 60Hz. When I tested my...
