Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I am using NRF52840 Dongle to scan all the BLE advertisement packets.
I wish to scan for the BLE advertisements packets only from a particular device using the whitelisting...
hello all,
i am trying to add ble app uart feature in other ble app project. so i am trying to change those defines variable, NRF_SDH_BLE_GATT_MAX_MTU_SIZE & NRF_SDH_BLE_VS_UUID_COUNT...
1. In the ssdk:ncs v1.3 Example: in 10_hello_world_clock_gettime, test function: clock_gettime (CLOCK_MONOTONIC, last_action_time);
The following error occurred at compile...
Hello,
nRF52811, SDK16.0, Softdevice7.0.1
We had developed our application based on nRF Blinky Android sample app for nRF52840. Now we want to port same app for nRF52811...
Hi,
I would like to ask if it is possible to use both Radio and NVMC at the same time (no SoftDevice)?
My scenario:
Start Radio and configure RX mode.
Write/erase...
Hello
I use nrf52840, Keil uvision 5.26, Win10.....
when i test the board, program run into hardware fault.
that reason is No I2C response, and i delete int the I2C...
I am developing a device which will have Nordic's UART service and it also need to be able to bond with the central. I am using SDK 12.0.0 and VisualGDB for my previous projects...
I'm working on getting an eclipse project working for my nRF52840 application that is currently working with a Makefile. My issue is that once I reset the board, or power...
Hi below is the function i am using to run garbage collection after deleting the data but the result i am getting was the same as before garbage collection.
I mean DIRTY_RECORDS_BEFORE_GC...
I have the following questions about PM and what it generates. My relevant board and config files are below, along with the PM partitions output.
1. Can you explain the...
I am using SDK v17 and Segger v4.52 but for some reason none of the print statements are being printed in the debug terminal. I think I had to enable these two things in sdk_config...
I am sending or trying to write character to ble_app_template but its giving error and its not receiving character.
this what i am trying to send-
if(strcmp((const char...
I see an ID that queries or prints RSRP/RSRQ/Cell ID-related information, but I don't see the AT instruction sq.E. for SINR, where can I print SINR information?
Hello guys,
Just received the Thingy91 and trying to upgrade the model firmware to v1.2 but it fails like this:
However I successfully been able to flash the modem firmware...
Hi Team,
We are using the nrf52840 soc for our application along with crypto engine (mbed TLS ) along with RNG, ECC, SHA256.
While validating the digital signature with...
