Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello
I am now using nrf52832 and BLE communication with an Android terminal.
BLE communication is a beginner.
I am using nRF_SDK_15.0.0_a53641.
Since I programmed...
It seems possible, but I can't quite figure out how to use nrf_ble_scan_filter_set to use more than one device name. Any assistance? Alternatively, is it possible to use wildcards...
Hi,
In GATT level, on the receiving side - Is it possible to receive a corrupted packet or does the LL identify and discards such packets?
Specifically
- Will host...
Hi
I segger project get compiled and download successfully but it didn't start work. After put it in debug mode, it start working even after removed it from debug mode working...
I am working on a custom board with two MCUs, one nRF52840 and one older MCU.
In the previous iteration of this PCB the old MCU was connected to USB through an FTDI FT232...
Hi,
I've developed a relay application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently...
Hi
My application with SDK11 S132 softdevice is having some unknown issues that will make wdt or hard fault handler happen. And I am trying to use the following code to...
Hello I am using eddystone-beacon example from sdk 12.3 but i am unable to get notification on android phone,nearby setting is also enabled ,please help??
Hello,
I’m looking for an example using the Segger IDE that would read the SAADC and transmit via BLE.
The following example seemed like a good starting place:
...
I am currently working with an nRF51822, SDK 10 (can't be changed), s110. I have a nRf51822-DK (aka pca10028) and wanted to try the d fu_dual_bank_ble_s110_pca10028 example...
I use the nrf_drv_pwm to generate a pwm sequence,
The sequence works fine, but between sequences and at the end I am unable to control the pin.
It is always high unless...
Hi guys
I am looking for export control related information on NRF52832-QFAA-R7, in particular: 1) Is the product a controlled dual use item under EU Regulation 428/2009...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
Hi,
I've been developing an application with the nRF9160 dev kit. We have just received the first rev of our custom hardware with an nRF9160 on it. I am trying to program...
Hello, we are facing an issue by connecting several sensors (UART nrf52832) to an Android Application ( Android Nougat 7.0) and we are facing disconnections (this happens...
