I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello,
I am trying to use an interupt from an analog devices ADXL343 accelerometer.
With a power supply of 3.0V to my board, I only get a 2.1V on the interrupt, and I...
Hello! What does the real marking of the nRF24L01 + chip look like? I have not such, but very similar. The problem is that the module after a while ceases to go to sleep,...
I am using a STlink to flash a nrf51822 module , and i am using Keil to do that, i flashed the module but when i am scanning it to find it in my mobile i cant find it, i doesn...
Hi ,
Does the Application update depend on bootloader version? . I changed the boot loader but application remains same on my device , hence the device is not booting up...
I have an application with three other tasks beside the sdh task. I'm trying to integrate softdevice to my existing freertos application, but soon after the task scheduler...
Hi,
What would be the procedure for updating the firmware of device through another host micro controller UART? (Not with PC tools like nrf go studio, nrf connect, nrf jprog...
Sir,
I have a MDBT50Q-UFL evaluation board. I am using Keil uVision 5 and flashing is done through ST-Link. I downloaded the example files from http://developer.nordicsemi...
Hi,
I have Ublox EVK-NINA-B3 on table, which has totally different pin layout than NRF52 DK (not sure why): https://www.u-blox.com/sites/default/files/EVK-NINA-B3_UserGuide_...
Hello everyone! I am a beginner and I need help in understanding advertising data. I am migrationg from SDK 13 to SDK 15.2. In SDK 13, the advertising data with manufacturer...
Dear Engineer,
work on sdk15.2, pca10040 eavl board. one as central run this code
\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\ble_central\ble_app_multilink_central...
I am starter developer of nRF51822 custom board.
in this board 16 mhz crystal is connected externally with XC1 and XC2 pins(37 & 38)
nRF5_SDK_12.1.0_0d23e2a rar file is...
Hello everyone,
I know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet.
For example: https://devzone...
(Mesh_v2.11, SDK_15.0.0, NRF52832)
Hello,
I wonder if a device can relay DFU packets even though mesh_relay is disabled by nrf_mesh_opt_set(NRF_MESH_OPT_NET_RELAY_ENABLE...
I am trying to set up the nrf52840 dongle on IAR using an I-jet for debugging. I have iar version 8.32.1. I am using example project ble_app_blinky from the ble_peripheral...
Hi I met a problem during programming a combo of HID on nrf52. I have set combo HID that have keyboard and multi touch. after pairing my smartphone(galaxy note 8), keyboard...
