I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hi,
I get a Mcu Mgr Error: 10 Group: 1, when I
start OTA on Android smart phone
interrupt during upload by disabling BLE on the phone
enable BLE again
retry OTA...
Hello,
I was using VS Code earlier today creating different build configurations for our hardware (nrf52840 and nrf9160 based) and everything was fine. I restarted the application...
I am currently using two nRF52840s to create a transmitter, one that acquires data and transmits it as advertisement data, and a receiver that receives data from the advertisement...
We are using nRF52833 with Softdevice S113 for BLE.
in the OS_Idle function, nrf_pwr_mgmt_run is called.
But never comes out of sleep.
Is there a need to call nrf_drv_power_sleepevt_init...
Good morning,
I am developing a RAK4631 (Nordic nRF52840 + Semtech LoRa SX1262) and now I need to manage the power consumption. My environment today is a VSCode/PlatformIO...
i am working with nrf52840 with nrf5-sdk 17.1.0 and with segger embedded studio 5.42a i am having trouble build a project and it is giving below warnings: Building 'main_app...
Hi,
I am trying to test the ICM42670 sensor using nRF9160 with Zephyr V2.6.0 and I am getting an errors when I init the sensor:
unexpected RESET_DONE_INT value, 0
ICM42670...
I’m using the nRF52832 with SDK 14.2.0 and would like to implement AES-128 CCM. Could you provide relevant documentation or instructions on how to achieve this?
I was developing my development kit with onboard sensors and other ICs. So, I was looking into NRF52 DK schematics and documentation. the problem is that the interface/debugger...
Hi,
I want to use the onboard 5340-DK QPSI flash for saving binary data into, however when i enable the support for it i get that the device is not ready. I have tried both...
The above is my code.
This is running log.
After scanning multiple times, my application may freeze, as shown in the log, and there will be no response after receiving...
I am developing a project on nRF9161.
I am interested in calculating data usage for different protocols (for example MQTT with TLS) when communicating with a server over...
Hi,
I refer to the method of the link below, which can generate factory_data.hex
https://docs.nordicsemi.com/bundle/ncs-latest/page/matter/nrfconnect_factory_data_configuration...
I am attempting to write a routine that monitors the heap in order to track down a memory leak. I've seen similar tools on other platforms and found them quite helpful. To...
