When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
I'm using the nrf52840DK and this example: "BLE Fundamentals, Lesson 4, Exercise 3," where you can send/receive strings between UART and Bluetooth. This works perfectly...
Hello,
I am encountering an issue with my Android OTA app after upgrading to Android 14. The OS seems to enforce the MTU size to 517 by default, but my device firmware ...
Hi,
(+) nPM1300 BUCK1 and BUCK2 efficiencies lower than expected - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
Has the above problem been fixed with...
Suppose we have a short distance communication between two nRF52840 devices. And suppose the receiver receives radio waves from other devices disturbing the connection (like...
I am unable to build my application for the Thingy:52 to perform FOTA over BLE. I have configured everything as outlined in the Nordic Developer Academy. FOTA over Bluetooth...
In my application I want to know if a DFU was executed successful and I'm using GPREGRET2 for it.
If a DFU as successful I'm writing GPREGRET2:
nrf_power_gpregret2_set...
Hi There,
I am trying to build a sample application (GNSS) on VS Code for my nRF9160 DK. The build used to be successful, but I noticed that it fails with the following...
Hello,
i am trying to install nRF Command-Line tools in my environment on my company's PC, i am on Windows 11 Enterprise on a Dell Precision 5820 Tower, and I am following...
I am unable to build my application for the Thingy:52 to perform FOTA over BLE. I have configured everything as outlined in the Nordic Developer Academy. FOTA over Bluetooth...
There is a lack of guidance on Blob Transfer Server/Client, so I decided to create and contribute a sample.
In Case ID: 331920, had the idea to add a BLOB Server and Client...
Hello Team,
We wanted to use a NOR Flash GD25Q32E to replace MX25R6435F which is using on the development kit. But we got an error. Please see below screen captures. ...
We are getting below error when flashing hex file in our custom board using a programmer tool but not getting the error when flashing using visual studio flash. 2024-10-15...
Hai,
We are planning to develop a Bluetooth gateway based on nrf52840.
the nrf is connected to esp32 through uart.
The duty of the nrf52840 is
1. It should receive...
Hi,
I'm using nRF Connect SDK v2.7.0 (this error happens with v2.5.0 as well). I'm trying to build the USB Mass Storage sample for FAT FS on flash, in zephyr/samples/subsys...
