Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I have connected the nRF52840 DK to the nPM1300 EVK , with the DK powered from BUCK1 output of the nPM1300.
When I supply 3 V or higher to the VBAT pin of the nPM1300...
Hi,
I’m evaluating the NUS (Nordic UART Service) as a way to stream and receive byte arrays.
I’ve noticed that there are two different implementations of the NUS service...
Affecte d SDK : n RF Connect SDK v 3.2.0 (Zephyr v 4. 2.9 9)
File : z ephyr/drivers/i2c /i2c_nrf x_twi.c
Description
The I2C TWI driver always returns - EIO for every...
I have been reviewing the datasheet of the BLE audio nRF5340. It lists multiple power rails in power section.
Is any power-on sequence required for the SOC.
Also, can...
Using NCS 3.1.0 - getaddrinfo with "offloaded sockets" (nrf9160/51) and ipv6 results in struct sockaddr_in6, where some "c struct padding bytes" (the last 3 of 24 bytes) are...
I flashed the thingy91x using NRFCloud connect. Provisioned it in nrfcloud using hologram SIM cards. How do I turn on air quality and all other sensor information?
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
New project using Nordic platform and I need to send multiple commands (32bit fixed size) to a device quickly using SPI with the CS toggling between each. I just want to confirm...
Hi Nordic Team,
I am currently developing a commercial product using the nRF Connect SDK (NCS) . The system consists of several nRF52 peripherals and a PC-based application...
On the nRF9151dk, the transmission line coming from the nRF9151 starts with a 0.1 mm trace width and a 0.46 mm gap, which corresponds to a 50 Ω characteristic impedance. However...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I am trying to run a simple button event yet callback is not fired when
CONFIG_PM_DEVICE_RUNTIME...
Hi
Could you provide nPM1300 NTC pin inside structure?(pull up resistor value, pull up voltage, others..)
And I want to know how to calculated NTC temperature by measured...
Hello everyone,
We'd like to use the rom_report and ram_report commands to be able to see (with a somewhat granularity) how much ROM and RAM do specific feature use so that...
Hi,
Question on the nRF7002. Can it be used as a hotspot to support 5 -10 wifi clients?
Basically, the need may be to download user manuals on site with a tablet.
...
