Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I am using NRF52840dk boards to make an openThread mesh network with CoAP. There is an example in NRF-SDK for coap client and another example for coap server. I used them...
I know there is an ongoing global semiconductor crisis. In the products, we decided to switch to NRF52/53 family products as core MCU. However, we're having hard time getting...
Hi,
Currently our system is using printf() to print some debug messages to the Segger debug terminal. Now we would like to reroute these messages to a UART port.
We are...
Hi there,
My nrf52840 DK seems dead. I want to recover it.
What I did:
Put the nrf52840 DK into Bootloader mode by pressing the "IF BOOT/RESET" button while powering...
Hi,
I'm working with pc-ble-driver and a PCA10040 devkit.
First, the central sends a data length update:
This returns no error (0), and on the BLE_GAP_EVT_DATA_LENGTH_UPDATE...
Hello,
we have a question about the usage of FDS. The data to save has a length of 1200 words. So the virtual page size is set to:
#define FDS_VIRTUAL_PAGE_SIZE 2048...
Hello,
I am using "pheripheral heartrate" example on SES, but I can not integrate SPI or ADC. How can I add "nrf_spi.h" and "nrf_adc.h" and relative C files on that project...
I'm using an NRF52811 and trying to configure the UARTE for Tx & Rx at 57600 baud but I'm having trouble with the Rx. I think I am dropping bytes and so want to try and exploit...
Hi,
please find attached some patches to improve the code quality of the SDK
1. Make ble_db_discovery_evt_t a const ptr
2. make p_string in ble_nus_c_string_send...
Hello,
i just loaded compilled peripheral_uart project without modification from nrfConnect sdk v1.5.1 to nrf52840 of the nrf9160 dk
and here is the output on uart output...
Hi, I successfully implemented a custom BLE service using this tutorial from Nordic. Also, thanks to a Nordic engineer, I have the QSPI example merged with the ble_app_template...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
Shalom!
In my central nrf52840 board we connect to a TI BLE sensor that has a customer UUID base service and the TI OAD base service both with 128 UUIDs. I succeeded in...
Hi all,
In my project am sending ecg values over ble to android app. During first connection, the values are received and seems to be no problem, but when i disconnect and...
