Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Working on the nRF52833DK board and based off the nrfx_spim_spis advanced non-blocking example sample. I've already converted the SPI master to use the Zephyr driver instead...
Hi all :
I am trying to use the nRF54L15 built-in load capacitor for crystal but I do not know how to measure the crystal performance, such as driving level and negative...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK using libraries from Nordic (nrfx_rtc.h, nrfx_clock.h and hal/nrf_rtc.h). I am not...
Hello everybody,
I am trying to get the RTC0 peripheral working on Nordic nrf9151-DK. I wanna use zephyr/driver_rtc.h library and zephyr/device.h librrary. I am able to...
Hi, We are trying to get our nRF54L15 running, but are running into clock issues. The hardware is configured without an external 32kHz crystal, so we want to rely on the NRF54...
Hi, The Kconfig fragment CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU is awesome to quickly get BLE OTA working. However, when going in depth, we can see that it's implying:
...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
